Nokia 4A0-AI1 Exam - Topic 1 Question 24 Discussion

Actual exam question for Nokia's 4A0-AI1 exam

Question #: 24
Topic #: 1

Which of the following system actions will pause a workflow at some point and wait for an operator to confirm or deny a particular course of action?

Astd. sleep

Bnsp.wait

Cnsp.user_input

Dnsp.pause_before

Show Suggested Answer

Suggested Answer: C

According to the NSP Intent Manager Application Help, an intent type has to be inReleasedstate for Intent Manager to provision a request.An intent type can be in Draft, Released or Phased-out state. A Draft state means that the intent type is under development and cannot be used for provisioning.A Phased-out state means that the intent type is no longer supported and cannot be used for provisioning

by Nana at May 17, 2024, 09:46 AM

Limited Time Offer

25%

Off

Get Premium 4A0-AI1 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Danilo

8 months ago

Really? I didn't think nsp.user_input was the right answer.

upvoted 0 times

...

Barrie

8 months ago

I thought std. sleep would do that too, but maybe not?

upvoted 0 times

...

Abraham

8 months ago

Wait, isn't nsp.wait also a valid option?

upvoted 0 times

...

Tegan

8 months ago

Yeah, I agree with that!

upvoted 0 times

...

Rodolfo

9 months ago

I'm pretty sure it's nsp.user_input.

upvoted 0 times

...

Elroy

9 months ago

I’m confused about nsp.pause_before; I thought it was just for delays, not for waiting on user input.

upvoted 0 times

...

Blossom

9 months ago

I practiced a similar question, and I feel like nsp.user_input was the one that explicitly waits for confirmation.

upvoted 0 times

...

Dyan

9 months ago

I'm not entirely sure, but I remember something about nsp.wait being used for pauses. Could that be it?

upvoted 0 times

...

German

9 months ago

I think the answer might be nsp.user_input since it sounds like it involves waiting for a user response.

upvoted 0 times

...

Jutta

9 months ago

I think the key here is looking for the action that specifically pauses the workflow and waits for user input. Based on that, I'm going to go with nsp.user_input.

upvoted 0 times

...

Huey

9 months ago

I'm a bit confused on this one. I'll need to review the system actions more closely to figure out the best option.

upvoted 0 times

...

Jeff

9 months ago

Wait, I'm not sure about that. Wouldn't nsp.pause_before be the right choice here? That seems like it would do what the question is asking for.

upvoted 0 times

...

Gwenn

9 months ago

Okay, let's see. I'm pretty sure the answer is nsp.user_input, since that would allow the workflow to pause and wait for user confirmation.

upvoted 0 times

...

Gilma

10 months ago

Hmm, this seems like a tricky one. I'll need to think through the options carefully.

upvoted 0 times

...

Mindy

10 months ago

Hmm, I'm not sure if deleting the entire contact record is the best approach. Maybe option D would be better - selecting the Do Not Email, Do Not Contact, and Email Opt Out fields to prevent any further communication.

upvoted 0 times

...

Oretha

10 months ago

I'm a bit unsure about whether the Email Poller counts as a separate license since it runs 24/7.

upvoted 0 times

...

Kaycee

10 months ago

This looks pretty straightforward. I'll start by checking the repo file and installing the RHVM package, then run the engine-setup command to configure it.

upvoted 0 times

...

Kimbery

10 months ago

Okay, I've got this. SIAM is all about integrating service delivery, so the correct answer has to be either B or C. I'll go with C since it mentions a single point of control.

upvoted 0 times

...