Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

NetApp NS0-184 Exam - Topic 8 Question 74 Discussion

Actual exam question for NetApp's NS0-184 exam
Question #: 74
Topic #: 8
[All NS0-184 Questions]

After the installation of a new ONTAP 9.8 cluster, you have to verify if AutoSupport works.

In this scenario, which two commands would you use to accomplish this task? (Choose two.)

Show Suggested Answer Hide Answer
Suggested Answer: A, B

by Anglea at Aug 13, 2025, 11:37 PM

Limited Time Offer

25%

Off

Get Premium NS0-184 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Caprice
3 months ago
Wait, can you really use D for verification? Sounds odd.
upvoted 0 times
...
Colby
3 months ago
A and D are the ones I usually use.
upvoted 0 times
...
Peggie
4 months ago
A and C are the go-tos, no doubt about it!
upvoted 0 times
...
Dorothea
4 months ago
I think B is also important, but not sure about A.
upvoted 0 times
...
Tracey
5 months ago
Definitely A and C for checking AutoSupport.
upvoted 0 times
...
Svetlana
5 months ago
I practiced a similar question, and I think "system node autosupport invoke" was about sending a test message, not checking the status.
upvoted 0 times
...
Teresita
5 months ago
I feel like "system node autosupport destination show" might also be relevant, but I can't recall if it directly verifies functionality.
upvoted 0 times
...
Felicidad
5 months ago
I think "system node autosupport check show" is definitely one of the commands we used in the lab to verify AutoSupport.
upvoted 0 times
...
Susana
6 months ago
I remember practicing with the AutoSupport commands, but I’m not entirely sure which ones are specifically for checking the status.
upvoted 0 times
...
Caitlin
6 months ago
I'm not too familiar with the ONTAP 9.8 commands, but I'll give it my best shot and try options B and D to see if I can get AutoSupport working.
upvoted 0 times
...
Mauricio
6 months ago
Easy peasy! I'd use options A and B to verify the AutoSupport history and check the current status.
upvoted 0 times
...
Josue
6 months ago
Okay, I'm a bit unsure about this one. I'll need to review the ONTAP 9.8 documentation to make sure I'm using the right commands.
upvoted 0 times
...
Audry
6 months ago
Hmm, this looks straightforward. I think I'll go with options B and C to check the AutoSupport configuration and destinations.
upvoted 0 times
...
Jillian
7 months ago
I agree with Nakita, that command would show the history of AutoSupport.
upvoted 0 times
...
Ruth
7 months ago
B and D, definitely. You need to check the AutoSupport status and also trigger a manual AutoSupport upload to make sure it's functioning properly.
upvoted 0 times
...
Elin
7 months ago
I think B and D are the correct commands to verify if AutoSupport is working. A and C don't seem to be the right options for this task.
upvoted 0 times
Hui
3 months ago
But B and D check and invoke, which is what we need!
upvoted 0 times
...
Cherry
4 months ago
A and C provide history and destination info, though.
upvoted 0 times
...
Shaquana
4 months ago
I agree with B and D. They seem more relevant.
upvoted 0 times
...
Lamonica
4 months ago
I believe A and C are the right choices.
upvoted 0 times
...
...
Nakita
8 months ago
I think I would use A) system node autosupport history show to check AutoSupport.
upvoted 0 times
...

Save Cancel