Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 350-801 Exam - Topic 9 Question 76 Discussion

Actual exam question for Cisco's 350-801 exam
Question #: 76
Topic #: 9
[All 350-801 Questions]

Refer to the exhibit.

Which codec should an engineer select for a call made between "Dallas-REG' & "Austin-REG'?

Show Suggested Answer Hide Answer
Suggested Answer: D

The codec preference list for the 'Dallas-REG' region is 'Factory Default low loss'. This list includes the following codecs in order of preference:


by Therese at May 12, 2024, 10:58 PM

Limited Time Offer

25%

Off

Get Premium 350-801 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Jaclyn
5 months ago
Are we sure G.729 is the best choice? Seems outdated.
upvoted 0 times
...
Billye
6 months ago
G.711 is too high bitrate for this scenario.
upvoted 0 times
...
Pearlene
6 months ago
Wait, why not OPUS? It’s newer and has lower bitrate!
upvoted 0 times
...
Leana
6 months ago
Totally agree, G.729 is solid for VoIP!
upvoted 0 times
...
Viki
6 months ago
G.729 is the codec for Dallas and Austin calls.
upvoted 0 times
...
Novella
7 months ago
I recall that G.729 is often preferred for low bandwidth, but I wonder if there are exceptions in specific cases.
upvoted 0 times
...
Vannessa
7 months ago
I practiced a similar question where G.711 was mentioned, but I believe G.729 is more efficient for VoIP calls.
upvoted 0 times
...
Lanie
7 months ago
I think both regions have the same codec list, so G.729 should be the right answer, but I need to double-check that.
upvoted 0 times
...
Cora
7 months ago
I remember studying the codec preferences, but I'm not entirely sure if G.729 is the best choice for this scenario.
upvoted 0 times
...
Donte
7 months ago
Hmm, I need to review my knowledge on audio codecs. There are a lot of options here, but I think G.729 is the way to go since it's the default low-loss codec for both regions.
upvoted 0 times
...
Tanja
7 months ago
The question is straightforward - the codec preference list is the same for both regions, so the common codec between them is G.729. This is the correct answer.
upvoted 0 times
...
Cornell
7 months ago
Based on the information provided, G.729 seems to be the optimal codec for this call between Dallas-REG and Austin-REG. It's a low-bitrate codec that provides good quality speech, which aligns with the "Factory Default low loss" preference.
upvoted 0 times
...
Simona
7 months ago
I'm a bit confused by all the different codec options. Can someone explain the key differences between them and why G.729 would be the best choice here?
upvoted 0 times
...
Glendora
7 months ago
The codec preference list for both regions is the same, so the codec that will be used is G.729.
upvoted 0 times
...
Catherin
7 months ago
Hmm, I'm a bit confused by the details here. I'll need to make sure I understand the requirements and the context before I can decide on the right query.
upvoted 0 times
...
Huey
7 months ago
This one seems straightforward. I think the answer is vSphere Motion, which allows live migration of VMs between hosts without downtime.
upvoted 0 times
...
Huey
8 months ago
I'm a bit confused here. Wouldn't "umount /dev/sdb3" just unmount the partition, not erase the data?
upvoted 0 times
...

Save Cancel