Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 350-801 Exam - Topic 6 Question 60 Discussion

An engineer troubleshoots outbound can failure on an ISDN-PRI circuit. The engineer ts suspecting the 'Incomplete Destination". Which debugs or commands are run in the voice gateway to troubleshoot the issue?
C) debug isdn q931 show isdn status
A) debug isdn q921 term mon
B) debug voip ecapi inout show controller ti
D) debug isdn q921 debug voip ecapi inout

Cisco 350-801 Exam - Topic 6 Question 60 Discussion

Actual exam question for Cisco's 350-801 exam
Question #: 60
Topic #: 6
[All 350-801 Questions]

An engineer troubleshoots outbound can failure on an ISDN-PRI circuit. The engineer ts suspecting the 'Incomplete Destination". Which debugs or commands are run in the voice gateway to troubleshoot the issue?

Show Suggested Answer Hide Answer
Suggested Answer: C

The engineer should run the following debugs or commands in the voice gateway to troubleshoot the issue:

debug isdn q931 - This debug will show the ISDN Q.931 messages that are being exchanged between the voice gateway and the ISDN switch. This can be used to identify the cause of the 'Incomplete Destination' error.

show isdn status - This command will show the status of the ISDN PRI circuit. This can be used to verify that the circuit is up and running.

The other options are not correct. The debug isdn q921 command will show the ISDN Q.921 messages that are being exchanged between the voice gateway and the ISDN switch. This is not necessary for troubleshooting the issue. The term mon command will show the terminal monitor output. This is not necessary for troubleshooting the issue. The debug voip ecapi inout command will show the VoIP ECAP messages that are being exchanged between the voice gateway and the VoIP server. This is not necessary for troubleshooting the issue. The show controller ti command will show the status of the T1 controller. This is not necessary for troubleshooting the issue.


by Van at Jul 03, 2023, 08:29 AM

Limited Time Offer

25%

Off

Get Premium 350-801 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Derick
9 months ago
Incomplete destination? Sounds tricky, not sure about these options.
upvoted 0 times
...
Eden
10 months ago
C is solid, but I’ve had luck with D too!
upvoted 0 times
...
Corrinne
10 months ago
Wait, are we sure about B? Seems off to me.
upvoted 0 times
...
Gwen
10 months ago
I think A could also help, but C is more specific.
upvoted 0 times
...
Deja
10 months ago
Definitely C, that's the go-to for ISDN issues.
upvoted 0 times
...
Dana
11 months ago
I might be mixing things up, but I think "debug voip ecapi inout" could help with analyzing the call flow.
upvoted 0 times
...
Jesus
11 months ago
I feel like "debug isdn q921" was mentioned in a similar practice question, but I can't remember if it was for outbound calls specifically.
upvoted 0 times
...
Lindy
11 months ago
I think "show isdn status" is important too, but I can't recall if it was part of the same command set we discussed.
upvoted 0 times
...
Marvel
11 months ago
I remember we practiced using "debug isdn q931" for troubleshooting ISDN issues, but I'm not sure if that's the right choice here.
upvoted 0 times
...
Elinore
11 months ago
I'm a bit confused by the `Even` struct and how it's being used in the `count_if` function. Is it just checking if each element is even? I'll need to double-check the syntax and logic to make sure I understand what's happening.
upvoted 0 times
...
Emiko
11 months ago
I'm feeling confident about this one. I'm going to select option D - right clicking on the dashboard tab and setting it as the default.
upvoted 0 times
...

Save Cancel