Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-615 Exam - Topic 6 Question 89 Discussion

Refer to the exhibit.Refer to the exhibit. VSAN traffic is not routed as expected. Which action should be taken to resolve the issue?
A) Reset the error packet counter
B) Configure the hello timer to match the neighbor
C) Configure the FSPF dead interval with a value higher than 80 seconds
D) Reset the inactivity timer on switch-2

Cisco 300-615 Exam - Topic 6 Question 89 Discussion

Actual exam question for Cisco's 300-615 exam
Question #: 89
Topic #: 6
[All 300-615 Questions]

Refer to the exhibit.

Refer to the exhibit. VSAN traffic is not routed as expected. Which action should be taken to resolve the issue?

Show Suggested Answer Hide Answer
Suggested Answer: A

by Georgiann at May 28, 2024, 01:04 AM

Limited Time Offer

25%

Off

Get Premium 300-615 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Raylene
9 months ago
Definitely need to check the hello timer settings first.
upvoted 0 times
...
Mignon
9 months ago
Wait, resetting the inactivity timer? That seems too simple!
upvoted 0 times
...
Mari
10 months ago
Isn't the FSPF dead interval usually set lower than 80 seconds?
upvoted 0 times
...
Salina
10 months ago
I disagree, I think resetting the error packet counter might help.
upvoted 0 times
...
Chantell
10 months ago
Option B is usually the go-to for neighbor issues.
upvoted 0 times
...
Leila
10 months ago
I’m leaning towards option C, but I’m not confident about the FSPF dead interval specifics. It’s been a while since we covered that.
upvoted 0 times
...
Johna
11 months ago
I feel like resetting the error packet counter might help, but it seems too simple for a routing issue.
upvoted 0 times
...
Claudia
11 months ago
I think we practiced a question similar to this where adjusting timers helped with routing issues. Could be option B?
upvoted 0 times
...
Nickie
11 months ago
I remember something about the hello timer being crucial for neighbor relationships, but I'm not entirely sure if that's the right choice here.
upvoted 0 times
...
Linn
11 months ago
Resetting the error packet counter seems like a good first step, but I'm not sure if that will fully resolve the issue. I'll need to consider the other options as well.
upvoted 0 times
...
Kanisha
11 months ago
Okay, let's see here. The question is asking about VSAN traffic not being routed as expected, so I'll need to focus on the networking and routing aspects.
upvoted 0 times
...
Maryrose
11 months ago
Hmm, this looks like a tricky one. I'll need to carefully review the exhibit and options to determine the best course of action.
upvoted 0 times
...
Walton
11 months ago
Configuring the hello timer to match the neighbor could be a potential solution, but I'll need to double-check the details to make sure that's the right approach.
upvoted 0 times
...
Daniel
11 months ago
Hmm, I'm a bit unsure about the differences between these options. I'll need to re-read the question carefully.
upvoted 0 times
...
Filiberto
11 months ago
Okay, I think I've got this. Facility FRR creates a detour protection tunnel for the LSP, so option D is the correct answer. The other options don't quite match what I know about how facility FRR works.
upvoted 0 times
...
Onita
1 year ago
Maybe we should just throw the whole switch-2 out and start over. That's the kind of technical advice I'd expect from my grandparents.
upvoted 0 times
Elvera
1 year ago
If those don't work, we can consider resetting the inactivity timer on switch-2.
upvoted 0 times
...
Ilda
1 year ago
Maybe configuring the hello timer to match the neighbor could also help.
upvoted 0 times
...
Johna
1 year ago
Let's not be too hasty, we can try resetting the error packet counter first.
upvoted 0 times
...
...
Kimberlie
1 year ago
Ah, the age-old question of VSAN traffic routing. I wonder if the solution involves a magic spell or summoning a network genie. Option C sounds the most promising, though.
upvoted 0 times
Glenn
1 year ago
C) Configure the FSPF dead interval with a value higher than 80 seconds
upvoted 0 times
...
Gerardo
1 year ago
B) Configure the hello timer to match the neighbor
upvoted 0 times
...
Tasia
1 year ago
A) Reset the error packet counter
upvoted 0 times
...
...
Veronika
1 year ago
Reset the inactivity timer on switch-2? Isn't that like trying to fix a broken window by painting the door? I'm not feeling too confident about that one.
upvoted 0 times
...
Cammy
1 year ago
The hello timer? Really? That seems like a shot in the dark. I'd go with option C - it sounds like the most logical solution to the problem at hand.
upvoted 0 times
Jamie
1 year ago
User2: I disagree, I believe configuring the FSPF dead interval with a value higher than 80 seconds is the way to go.
upvoted 0 times
...
Bette
1 year ago
User1: I think resetting the error packet counter might help.
upvoted 0 times
...
...
Iola
1 year ago
I believe configuring the hello timer to match the neighbor might also be a good solution.
upvoted 0 times
...
Estrella
1 year ago
I agree with Simona. Resetting the error packet counter should help resolve the issue.
upvoted 0 times
...
Carmen
1 year ago
Hmm, I think resetting the error packet counter might be a good place to start, but I'm not sure that's the root cause here. Maybe we should look into configuring the FSPF dead interval instead?
upvoted 0 times
...
Simona
1 year ago
I think the correct action is to reset the error packet counter.
upvoted 0 times
...

Save Cancel