Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-615 Exam - Topic 6 Question 128 Discussion

You have an ACI environment with three APICs, two spine switches, and four-leaf switches. You wipe and reboot all APICs first then leaf and spine switches one-by-one and successfully go through the Initial Setuo dialogue on the APIC 1 CIMC KVM console. When you log in to the APIC1 WebGUI, you notice that you do not see any directly connected leaf switches being discovered under Fabric > Inventory > Fabric Membership. What is the cause of the issue?
C) You forgot to enter the TEP Pool value during the Initial Setup dialogue on APIC1.
A) The leaf nodes were not erased properly, which caused a fabric parameters mismatch with the APIC1.
B) Rebooting the APICs and the leaf and spine switches after wiping them is not required.
D) The same Fabric Name value should be used before after wiping all devices.

Cisco 300-615 Exam - Topic 6 Question 128 Discussion

Actual exam question for Cisco's 300-615 exam
Question #: 128
Topic #: 6
[All 300-615 Questions]

You have an ACI environment with three APICs, two spine switches, and four-leaf switches. You wipe and reboot all APICs first then leaf and spine switches one-by-one and successfully go through the Initial Setuo dialogue on the APIC 1 CIMC KVM console. When you log in to the APIC1 WebGUI, you notice that you do not see any directly connected leaf switches being discovered under Fabric > Inventory > Fabric Membership. What is the cause of the issue?

Show Suggested Answer Hide Answer
Suggested Answer: C

by Karl at Jun 30, 2026, 01:38 AM

Limited Time Offer

25%

Off

Get Premium 300-615 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Robt
4 days ago
I lean towards D. Fabric Name consistency is key after a wipe.
upvoted 0 times
...
Salena
9 days ago
True, but I feel like A is more likely. The wipe is crucial.
upvoted 0 times
...
Annice
14 days ago
What about option C? Missing the TEP Pool value could cause issues too.
upvoted 0 times
...
Abraham
20 days ago
I agree, A makes sense. Fabric parameters need to match.
upvoted 0 times
...
Becky
25 days ago
I think it's option A. The leaf nodes might not have been wiped correctly.
upvoted 0 times
...
Stephaine
30 days ago
I doubt it's the TEP Pool; that seems too simple for such a big issue.
upvoted 0 times
...
Micaela
1 month ago
Rebooting isn't necessary, right? Seems like a waste of time.
upvoted 0 times
...
Val
1 month ago
Wait, you have to use the same Fabric Name after wiping? That's new to me!
upvoted 0 times
...
Aliza
2 months ago
I think it's definitely a fabric parameters mismatch.
upvoted 0 times
...
Jamal
2 months ago
Sounds like a TEP Pool issue to me.
upvoted 0 times
...
Evette
2 months ago
I feel like if the leaf nodes weren't erased properly, it could definitely cause a mismatch with the APIC. That sounds familiar.
upvoted 0 times
...
Ronnie
2 months ago
I practiced a similar question, and I think rebooting after wiping isn’t necessary, but I could be wrong about that.
upvoted 0 times
...
Sage
2 months ago
I’m not entirely sure, but I think the fabric name needs to be consistent after wiping everything. That could be a factor.
upvoted 0 times
...
Larae
2 months ago
I remember something about the TEP Pool value being crucial during the setup, so maybe that's the issue here.
upvoted 0 times
...

Save Cancel