Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-615 Exam - Topic 10 Question 80 Discussion

The VXL AN fabric is deployed with this configuration:The VL AN 50 interface has no IP address on VTEP1 and VTEP4.The VLAN 100 interface has no IP address on VTEP2 and VTEP3. nve1 interface is configured on all VTEPs.Host A experiences timeouts when attempting to ping host B. Which set of actions allows host A to reach host B7
C) On VTEP1, associate VNI 50000 to Test Telco VRFOn VTEP4, associate VNI 50000 to Test Telco VRF.
A) On VTEP1, associate VNI 30000 to Test_ Telco VRF. On VTEP4, associate VNI 20000 to Test_ Telco VRF.
B) On VTEP2, associate VNI 55000 to Test Telco VRF. On VTEP4, associate VNI 50000 to Test Telco VRF.
D) On VTEP2, associate VNI 30000 to Test Telco VRF On VTEP4, associate VNI 20000 to Test Telco VRF

Cisco 300-615 Exam - Topic 10 Question 80 Discussion

Actual exam question for Cisco's 300-615 exam
Question #: 80
Topic #: 10
[All 300-615 Questions]

The VXL AN fabric is deployed with this configuration:

The VL AN 50 interface has no IP address on VTEP1 and VTEP4.

The VLAN 100 interface has no IP address on VTEP2 and VTEP3.

nve1 interface is configured on all VTEPs.

Host A experiences timeouts when attempting to ping host B. Which set of actions allows host A to reach host B7

Show Suggested Answer Hide Answer
Suggested Answer: C

by Loren at Jan 25, 2024, 09:50 PM

Limited Time Offer

25%

Off

Get Premium 300-615 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Jessenia
9 months ago
Not sure about that, seems too simple!
upvoted 0 times
...
Willard
9 months ago
I think option A makes the most sense here.
upvoted 0 times
...
Cyril
10 months ago
Wait, how does that affect the VNIs?
upvoted 0 times
...
Merilyn
10 months ago
Totally agree, that’s a key point!
upvoted 0 times
...
Rolf
10 months ago
VTEP1 and VTEP4 have no IPs, right?
upvoted 0 times
...
Rasheeda
10 months ago
I think option A might be the right choice since it mentions VTEP1 and VTEP4, but I’m not entirely confident about the VNI numbers.
upvoted 0 times
...
Kasandra
11 months ago
I’m a bit confused about the VTEP interfaces without IP addresses. Does that affect how we associate the VNIs?
upvoted 0 times
...
Germaine
11 months ago
This question feels similar to the practice ones we did on VTEP configurations. I think associating the correct VNIs is crucial for the VRF to work properly.
upvoted 0 times
...
Brice
11 months ago
I remember we discussed how VNI associations can impact connectivity, but I'm not sure which specific VNIs to use here.
upvoted 0 times
...
Franklyn
11 months ago
Hmm, this is a tricky one. I'm not entirely sure, but I'll give it my best shot and try to eliminate the options that don't seem quite right.
upvoted 0 times
...
Adelle
11 months ago
I think I've got it! The answer is C - associating VNI 50000 to the Test Telco VRF on both VTEP1 and VTEP4. That should allow host A to reach host B.
upvoted 0 times
...
Graciela
11 months ago
I'm a bit confused by the different VLAN configurations on the VTEPs. I'll need to make sure I understand how that impacts the solution.
upvoted 0 times
...
Yvette
11 months ago
Okay, let me see if I can break this down step-by-step. The key seems to be associating the right VNIs to the Test Telco VRF on the correct VTEPs.
upvoted 0 times
...
Miesha
11 months ago
Hmm, this looks like a tricky one. I'll need to carefully analyze the information provided and think through the different options.
upvoted 0 times
...
Elin
11 months ago
Hmm, I'm a bit unsure about this one. The question is asking for two routes, but there are four options. I'll need to analyze each one closely to determine the best two choices.
upvoted 0 times
...
Jesus
11 months ago
This looks like a straightforward question about the Catalyst 2960-L switch. I think the key is to focus on the "get a small branch or office network running within minutes" part of the question.
upvoted 0 times
...
Otis
11 months ago
I've got a good feeling about this. The options give me a few possibilities to consider, and I think I can narrow it down based on my understanding of MVPN label allocation.
upvoted 0 times
...
Maxima
2 years ago
Haha, yeah, that would be a real plot twist. But let's not jinx ourselves, shall we? Option D it is!
upvoted 0 times
...
Luis
2 years ago
Ooh, good catch! I think you're right. Option D seems to be the most logical solution to the problem.
upvoted 0 times
...
Nieves
2 years ago
You know, I'm actually leaning towards Option D. That one associates the correct VNIs (30000 and 20000) to the Test Telco VRF on the respective VTEPs.
upvoted 0 times
Celestina
2 years ago
G: Agreed, hopefully that resolves the ping timeouts Host A is facing.
upvoted 0 times
...
Malcolm
2 years ago
F: Let's go ahead and implement those changes on the VTEPs to fix the issue.
upvoted 0 times
...
Tresa
2 years ago
E: Looks like Option D is the way to go then.
upvoted 0 times
...
Gerald
2 years ago
D: Exactly, that's how the configuration should be for host A to reach host B.
upvoted 0 times
...
Bok
2 years ago
C: So, VTEP2 gets VNI 30000 and VTEP4 gets VNI 20000, right?
upvoted 0 times
...
Ariel
2 years ago
B: Yeah, that should help resolve the timeouts Host A is experiencing.
upvoted 0 times
...
Stephaine
2 years ago
A: Option D makes sense, it associates the correct VNIs to the Test Telco VRF on the VTEPs.
upvoted 0 times
...
...
Edison
2 years ago
Alright, let's go with Option D then. I'm feeling confident about that one. Although, it would be hilarious if the answer was actually something completely different, just to mess with us.
upvoted 0 times
...

Save Cancel