Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-615 Exam - Topic 1 Question 59 Discussion

Refer to the exhibit.Refer to the exhibit. A network engineer must use BGP to route IPv4 and IPv6 routes between R1 and R2. The IPv4 addresses are exchanged as expected between the routers through BGP. The routers have reached an Established BGP state. However, the IPv6 routes from R2 fail to show in the routing table of R1. Which action resolves the issue?
A) Create a route map that sets the IPv6 next hop.
B) Advertise L2VPN EVPN under IPv4 unicast address family
C) Configure an IPv6 BGP neighbor on R1
D) Enable IPv6 routing on R1

Cisco 300-615 Exam - Topic 1 Question 59 Discussion

Actual exam question for Cisco's 300-615 exam
Question #: 59
Topic #: 1
[All 300-615 Questions]

Refer to the exhibit.

Refer to the exhibit. A network engineer must use BGP to route IPv4 and IPv6 routes between R1 and R2. The IPv4 addresses are exchanged as expected between the routers through BGP. The routers have reached an Established BGP state. However, the IPv6 routes from R2 fail to show in the routing table of R1. Which action resolves the issue?

Show Suggested Answer Hide Answer
Suggested Answer: A

by Mollie at Oct 13, 2022, 10:32 PM

Limited Time Offer

25%

Off

Get Premium 300-615 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Dottie
10 months ago
I thought we needed to configure the neighbor first, though.
upvoted 0 times
...
Wilda
10 months ago
A route map for the next hop sounds interesting too.
upvoted 0 times
...
Gerald
10 months ago
Wait, are we sure that's the only fix?
upvoted 0 times
...
Tammy
11 months ago
Totally agree, D is the way to go!
upvoted 0 times
...
Veronique
11 months ago
You need to enable IPv6 routing on R1.
upvoted 0 times
...
Corinne
11 months ago
Enabling IPv6 routing seems like a straightforward solution, but I wonder if there's more to it than just that.
upvoted 0 times
...
Ryan
11 months ago
I feel like the next hop setting could be important, but I can't recall if it specifically applies to IPv6 in this scenario.
upvoted 0 times
...
Iraida
11 months ago
I think I saw a similar question where configuring a BGP neighbor was the key, but I'm not entirely sure if that's the case here.
upvoted 0 times
...
Hassie
11 months ago
I remember something about needing to enable IPv6 routing on the router for it to recognize those routes.
upvoted 0 times
...
Delmy
11 months ago
Okay, I think I've got it. Let me walk through this step-by-step and see if I can determine the correct output.
upvoted 0 times
...
Lavonda
11 months ago
Hmm, this looks like a tricky one. I'll need to carefully think through the dependencies and availability calculations to get the right answer.
upvoted 0 times
...
Jade
11 months ago
Hmm, this one seems tricky. I'll need to think carefully about the different view types and where hosted elements can be placed.
upvoted 0 times
...
Octavio
11 months ago
Time to market sounds like it might relate more to direct costs rather than indirect ones, doesn't it?
upvoted 0 times
...
Lauran
11 months ago
Hmm, I'm a bit confused on the OSI layers. Let me think this through carefully.
upvoted 0 times
...

Save Cancel