Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-410 Exam - Topic 14 Question 77 Discussion

A DMVPN network is preconfigured with tunnel 0 IP address 192.168.1.254 on the HUB, IP connectivity, crypto policies, profiles, and EIGRP AS 100. The NHRP password is ccnp123, and the network ID and tunnel key is EIGRP ASN Do not introduce a static route. Configure DMVPN connectivity between routers BR1 and BR2 to the HUB router using physical interface as the tunnel source to achieve these goals:
A) See the answer solution in Explanation

Cisco 300-410 Exam - Topic 14 Question 77 Discussion

Actual exam question for Cisco's 300-410 exam
Question #: 77
Topic #: 14
[All 300-410 Questions]

A DMVPN network is preconfigured with tunnel 0 IP address 192.168.1.254 on the HUB, IP connectivity, crypto policies, profiles, and EIGRP AS 100. The NHRP password is ccnp123, and the network ID and tunnel key is EIGRP ASN Do not introduce a static route. Configure DMVPN connectivity between routers BR1 and BR2 to the HUB router using physical interface as the tunnel source to achieve these goals:

Show Suggested Answer Hide Answer
Suggested Answer: A

ON BR1

ON BR2


by Cassi at Oct 22, 2023, 02:41 PM

Limited Time Offer

25%

Off

Get Premium 300-410 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Amie
9 months ago
I can't believe the NHRP password is that simple!
upvoted 0 times
...
Hildegarde
9 months ago
Totally agree, that could complicate things.
upvoted 0 times
...
Stephaine
10 months ago
Wait, no static route? That seems risky.
upvoted 0 times
...
Vivan
10 months ago
Yup, and EIGRP AS 100 is set!
upvoted 0 times
...
Bernadine
10 months ago
Tunnel 0 IP is 192.168.1.254, right?
upvoted 0 times
...
Crista
10 months ago
I’m pretty confident about the crypto policies, but I’m not sure how to verify the connectivity between BR1 and BR2 after the setup.
upvoted 0 times
...
Owen
11 months ago
I think I might have mixed up the tunnel key and network ID in my notes. I hope I remember the right syntax for the tunnel configuration!
upvoted 0 times
...
Lucille
11 months ago
This question feels similar to one we did in class about configuring EIGRP over DMVPN. I think I need to double-check the NHRP settings.
upvoted 0 times
...
Ben
11 months ago
I remember practicing DMVPN configurations, but I'm unsure about the exact commands for setting up the tunnel source.
upvoted 0 times
...
Georgeanna
11 months ago
This seems pretty straightforward. I'll just follow the instructions and configure the tunnel, NHRP, and EIGRP settings as specified. Shouldn't be too difficult.
upvoted 0 times
...
Alyce
11 months ago
The EIGRP AS number and tunnel key are given, so that should make it straightforward to get the routing protocol set up. I'll double-check the crypto policies and profiles too.
upvoted 0 times
...
Brande
11 months ago
No problem, I've done DMVPN configurations before. I'll make sure to use the physical interface as the tunnel source and configure the NHRP password and network ID correctly.
upvoted 0 times
...
Eileen
11 months ago
Hmm, I'm a bit confused about the tunnel source interface. Do I need to use the physical interface or can I use a loopback?
upvoted 0 times
...
Casey
11 months ago
Okay, this looks like a DMVPN configuration question. I'll need to configure the tunnel interface, NHRP, and EIGRP on the branch routers to connect to the hub.
upvoted 0 times
...
Pamella
11 months ago
I'm a bit confused by the options. Do we need to start the action from the asset configuration section, or is that not the right approach here?
upvoted 0 times
...
Emilio
11 months ago
This looks like a tricky one. I'll need to think through the different digital certificate formats I know to figure out the most widely accepted one.
upvoted 0 times
...
Willow
11 months ago
Okay, I've got this. A module is a database object that includes custom procedures coded using Visual Basic. That means it's a way to add more advanced functionality to an Access database beyond just the built-in features.
upvoted 0 times
...
Rashida
11 months ago
Hmm, I'm a little unsure about this one. The passage does say cloud computing is simple, but it doesn't explicitly state that the whole process is straightforward. I might need to think this through a bit more.
upvoted 0 times
...
Chun
11 months ago
I think option B might be correct because I remember discussing how defect detection is prioritized in STEP, but I'm not entirely sure.
upvoted 0 times
...
Kris
2 years ago
Yeah, the key things we need to configure are the tunnel source interface, NHRP password, and EIGRP AS number, right? I think if we just follow the topology and information provided, we should be able to figure this out.
upvoted 0 times
...
Yen
2 years ago
Alright, let's break this down step-by-step. The HUB is already preconfigured, so we just need to set up the spoke routers BR1 and BR2 to connect to it.
upvoted 0 times
...
Anissa
2 years ago
Haha, as long as we don't accidentally configure the tunnel key as 'password123' or something equally obvious! That would be a rookie mistake.
upvoted 0 times
...

Save Cancel