Leave a message
Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 0d 3h 17m 45s Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions

Salesforce Exam OmniStudio Consultant Topic 5 Question 49 Discussion

Actual exam question for Salesforce's OmniStudio Consultant exam
Question #: 49
Topic #: 5
[All OmniStudio Consultant Questions]

How should the consultant design the OmniScript solution to allow the user to stop and resume a process at a later time?

Show Suggested Answer Hide Answer
Suggested Answer: A, B, C

Contribute your Thoughts:

Carma
2 months ago
I'm with Rodrigo on this one. B. ResumeStep is the way to go. Unless, of course, you want your users to feel like they're navigating a never-ending maze of confusion. Not my cup of tea.
upvoted 0 times
Ryan
3 days ago
I think ResumeStep is the most user-friendly option for stopping and resuming a process.
upvoted 0 times
...
Nu
6 days ago
Yeah, ResumeStep makes it much easier for users to pick up where they left off.
upvoted 0 times
...
Carri
29 days ago
I agree with you, ResumeStep is definitely the way to go.
upvoted 0 times
...
...
Nakisha
2 months ago
Clearly, the answer is B. ResumeStep. Anything else would be like trying to herd cats while juggling chainsaws. Not worth the effort.
upvoted 0 times
Marica
18 days ago
Definitely, ResumeStep is the most efficient option.
upvoted 0 times
...
Amie
26 days ago
I agree, trying to use anything else would be too complicated.
upvoted 0 times
...
Fanny
1 months ago
D) Use a DataRaptor Post Action
upvoted 0 times
...
Rory
2 months ago
I think B) Configure a ResumeStep is the way to go.
upvoted 0 times
...
Doug
2 months ago
I agree, ResumeStep is the way to go.
upvoted 0 times
...
Raelene
2 months ago
B) Configure a ResumeStep
upvoted 0 times
...
...
Erick
2 months ago
Ah, the age-old question of how to design a solution that allows users to stop and resume. I'd go with B. ResumeStep is the way to go, no doubt about it.
upvoted 0 times
...
Izetta
3 months ago
I was leaning towards C. Using an Integration Procedure, but after re-reading the question, I think B is the better choice. Resuming the process is key here.
upvoted 0 times
Brittney
1 months ago
I think B is the right choice too. It's important for the user to be able to pick up where they left off.
upvoted 0 times
...
Rashad
2 months ago
Configuring the Save property could also be a good choice to allow the user to stop and resume the process.
upvoted 0 times
...
Adolph
2 months ago
Using an Integration Procedure might not be the best option for this specific requirement.
upvoted 0 times
...
Brittney
2 months ago
I agree, B seems like the best choice for allowing the user to resume the process later on.
upvoted 0 times
...
Jolene
2 months ago
I agree, configuring a ResumeStep would allow the user to stop and resume the process at a later time.
upvoted 0 times
...
Glory
2 months ago
I think B is the better choice. Resuming the process is key here.
upvoted 0 times
...
...
Rodrigo
3 months ago
Hmmm, I think the correct answer is B. Configuring a ResumeStep seems like the most straightforward way to allow users to stop and resume the process.
upvoted 0 times
...
Amber
3 months ago
I believe using an Integration Procedure could also be a good option for allowing the user to stop and resume the process.
upvoted 0 times
...
Jestine
3 months ago
I agree with Eladia. Configuring a ResumeStep would allow the user to stop and resume the process.
upvoted 0 times
...
Eladia
3 months ago
I think the consultant should configure a ResumeStep.
upvoted 0 times
...

Save Cancel
a