PeopleCert Exam 19 Topic 7 Question 55 Discussion

Actual exam question for PeopleCert's 19 exam

Question #: 55
Topic #: 7

[All 19 Questions]

The reason(s) for not marking the customer Specification Limits (SL) on a Control Chart is which of these? (Note: There are 4 correct answers).

AProcess control teams should not control a process based on SLs

BDisplaying the SLs on a Control Chart sends a wrong signal toward process control

CMarking the SLs on a Control Chart is against the principle of charting

DBy marking the SLs, one can confuse the operator as to what limits are critical

EBy using mere Control Limits the process only needs to be in Statistical Control

Show Suggested Answer

Suggested Answer: A

by Novella at Jun 02, 2024, 04:11 AM

Limited Time Offer

25%

Off

Get Premium 19 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Vincenza

1 years ago

I'm with the crowd on this one - B is the correct answer. Gotta love those multiple-choice exams, am I right?

upvoted 0 times

Judy

12 months ago

B) Repeatability & Reproducibility

upvoted 0 times

...

Felton

12 months ago

A) Stability, Bias & Linearity

upvoted 0 times

...

Noble

1 years ago

I was tempted by C, but you can't have accuracy without addressing repeatability. B is the way to go.

upvoted 0 times

Mari

1 years ago

Yes, B covers both repeatability and reproducibility.

upvoted 0 times

...

Delpha

1 years ago

I agree, repeatability is crucial for accuracy.

upvoted 0 times

...

Shakira

1 years ago

Haha, I bet the test-makers threw in that 'Stability' term to trip people up. But I'm sticking with B.

upvoted 0 times

Arlette

1 years ago

I'm not sure, but I think it might be D) Precision & Sensitivity.

upvoted 0 times

...

Leota

1 years ago

I agree, I'm going with B) Repeatability & Reproducibility.

upvoted 0 times

...

Keneth

1 years ago

I think it's A) Stability, Bias & Linearity.

upvoted 0 times

...

Denna

1 years ago

I agree with Salena, those factors are crucial for ensuring accurate measurements.

upvoted 0 times

...

Isaac

1 years ago

Hmm, I was debating between B and D, but I'll go with B. Precision and sensitivity are important, but they aren't the whole story.

upvoted 0 times

...

Malcolm

1 years ago

I think the answer is B. Repeatability and Reproducibility. Those are key aspects of measurement system accuracy.

upvoted 0 times

Willow

1 years ago

I think stability, bias, and linearity are also key factors to consider.

upvoted 0 times

...

Bea

1 years ago

I agree, repeatability and reproducibility are important for accuracy.

upvoted 0 times

...

Malinda

1 years ago

Precision and sensitivity play a role in accuracy as well.

upvoted 0 times

...

Marcos

1 years ago

Yes, stability, bias, and linearity are also important factors to consider in the accuracy of a measurement system.

upvoted 0 times

...

Filiberto

1 years ago

I think stability, bias, and linearity are also important factors to consider.

upvoted 0 times

...

Dana

1 years ago

I agree, repeatability and reproducibility are crucial for accuracy.

upvoted 0 times

...

Silvana

1 years ago

I agree, repeatability and reproducibility are crucial for accurate measurements.

upvoted 0 times

...

Salena

1 years ago

I think the Accuracy of a Measurement System addresses Stability, Bias & Linearity.

upvoted 0 times

...