Free Huawei H35-481_V2.0 Exam Dumps August 2026

The GUI configuration mode in MAE-Deployment can be used to configure parameters in an MO and reconfigure a single NE. It cannot be used to configure parameters in multiple MOs or to batch reconfigure multiple NEs. According to the Huawei official documentation, 'The GUI configuration mode can be used to configure parameters in an MO and reconfigure a single NE. However, it cannot be used to configure parameters in multiple MOs or to batch reconfigure multiple NEs.'

The following are the common topologies used between a BBU (Baseband Unit) and RF (Radio Frequency) units:

1. Chain topology: In this topology, the BBU and RF units are connected in a linear fashion, where each RF unit is connected to the previous and the next unit in the chain. B. Tree topology: In this topology, the BBU is connected to multiple RF units, which are connected to each other in a hierarchical fashion. D. Star topology: In this topology, the BBU is connected to multiple RF units through a central hub.

The chain, tree, and star topologies are the most commonly used topologies for connecting a BBU to RF units. The ring topology is not commonly used for this type of connection. Sources: [1] Li, Y., Li, Y., Li, Y., Li, T., and Li, S. '5G wireless network topology research.' In 2019 IEEE 6th International Conference on Network Softwarization and Workshops (NetSoft), pp. 1-6, 2019. https://ieeexplore.ieee.org/document/8783934. [2] Gao, Y., and Wang, Y. '5G ultra-densification cell architecture research.' In 2019 IEEE International Conference on Communications Workshops (ICC Workshops), pp. 1-5, 2019. https://ieeexplore.ieee.org/document/8765036.

In IEEE 1588V2 frequency synchronization, all intermediate transmission devices must support the IEEE 1588V2 protocol. This means that all devices that are involved in transmitting the synchronization signal, such as routers and switches, must be able to process and pass on the IEEE 1588V2 messages. If any device in the path of the synchronization signal does not support the IEEE 1588V2 protocol, it will not be able to process and forward the messages, and the overall synchronization will be affected.

The UE inactivity timer on the NR side expiring and the air interface link on the NR side being abnormal, and a UE reporting SCG Failure Info to the eNodeB, can both trigger the MeNB to release the SgNB. Other actions, such as an inter-SgNB cell change or the MeNB detecting an abnormal X2 link, may also lead to SgNB release, but are not the trigger for it.

Extended Cyclic Prefix - an overview | ScienceDirect Topics

https://www.sciencedirect.com/topics/engineering/extended-cyclic-prefix

5G NR Numerology - Subcarrier Spcaing (SCS) - Techplayon

http://www.techplayon.com/5g-nr-numerology-subcarrier-spcaing-scs/

In Non-standalone (NSA) networking, X2 self-setup between a gNodeB and an eNodeB requires that the gNodeB and eNodeB be managed by the same OSS. Because gNodeB and eNodeB are managed by the same OSS, the OSS can configure the X2 self-setup parameters, such as the X2 self-setup switch, the X2 interface IP address, and the X2 self-setup trigger conditions. Only when the gNodeB and eNodeB are managed by the same OSS and configured with the same X2 self-setup parameters, the gNodeB and eNodeB can establish an X2 self-setup connection.

The segmentation method is the most important method for isolating faults on the transport network. Different methods are used for different fault types, such as Optical Time Domain Reflectometry (OTDR) for fiber faults, Radio Frequency Interference Measurement (RFI) for radio interference, and Signal-to-Noise Ratio (SNR) for signal noise. By segmenting the network, faults can be easily identified and isolated. Reference: https://www.cisco.com/c/en/us/td/docs/solutions/Enterprise/WAN_and_MAN/L2L3_VPN_Optimization_Solution/2-1_L2L3_VPN_Optimization_Solution_Chapter.html

In 5G Core network, the core network subscription information contains parameters that are used to manage the resources of a UE.

1. UE-AMBR (UE Aggregate Maximum Bit Rate) : It's the maximum bit rate that is allocated to a UE for non-guaranteed bit rate (non-GBR) services. It controls the non-GBR rate for a UE.

The destination address route configuration is not applicable when multiple IP addresses with different next hop addresses are planned for the gNodeB. Destination address route configuration is used when a single IP address is used by the gNodeB and the next hop address and outgoing interface do not need to be configured. In the case of multiple IP addresses with different next hop addresses, direct route configuration should be used. Direct route configuration requires that the IP address, next hop address, and outgoing interface all be specified for each IP address.