Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

HPE7-A08 Exam - Topic 3 Question 2 Discussion

Refer to the partial exhibit from an HPE Aruba Networking CX 8325:A new port 1/1/44 needs to be configured to connect to a 29301, which has the following configuration:Which configuration would be used?A.B.C.D.
A) Option A
B) Option B
C) Option C
D) Option D

HPE7-A08 Exam - Topic 3 Question 2 Discussion

Actual exam question for HP's HPE7-A08 exam
Question #: 2
Topic #: 3
[All HPE7-A08 Questions]

Refer to the partial exhibit from an HPE Aruba Networking CX 8325:

A new port 1/1/44 needs to be configured to connect to a 29301, which has the following configuration:

Which configuration would be used?

A.

B.

C.

D.

Show Suggested Answer Hide Answer
Suggested Answer: A

by Jody at Aug 13, 2025, 05:59 AM

Limited Time Offer

25%

Off

Get Premium HPE7-A08 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Jeannetta
8 months ago
Definitely leaning towards Option D for the configuration.
upvoted 0 times
...
Dolores
8 months ago
Not sure about these options, they all seem similar.
upvoted 0 times
...
Rodney
8 months ago
Surprised that Option A is even a contender!
upvoted 0 times
...
Cassie
9 months ago
I think Option C is better for this setup.
upvoted 0 times
...
Stacey
9 months ago
Option B looks like the right choice.
upvoted 0 times
...
Glennis
10 months ago
I remember that we discussed the importance of speed and duplex settings. I think option C might have those configured correctly, but I need to double-check.
upvoted 0 times
...
Alexis
10 months ago
I'm really uncertain about the correct settings for the trunk mode. I hope I can recall the right command syntax during the exam.
upvoted 0 times
...
Shawnna
10 months ago
I practiced a similar question where we had to configure a port, and I feel like option B might be the right choice because it looks familiar.
upvoted 0 times
...
Whitney
10 months ago
I think I remember that we need to match the VLAN settings from the 29301 configuration, but I'm not sure which option does that.
upvoted 0 times
...
Kirk
10 months ago
This is a good test of my understanding of Aruba port configuration. I'm going to carefully review the exhibit and options to determine the right choice.
upvoted 0 times
...
Georgeanna
11 months ago
I'm a little confused by the different port numbering formats. Is port 1/1/44 the same as port 44? I'll need to double-check how these ports are labeled.
upvoted 0 times
...
Lajuana
11 months ago
Okay, I think I've got this. Based on the port speed and duplex settings in the exhibit, Option B looks like the correct configuration to use.
upvoted 0 times
...
Detra
11 months ago
Hmm, I'm a bit unsure about this one. The port settings in the exhibit don't seem to match any of the options exactly. I'll need to analyze the details closely.
upvoted 0 times
...
Delfina
11 months ago
This looks like a straightforward configuration question. I'll carefully compare the port settings in the exhibit to the options provided.
upvoted 0 times
...
Monroe
12 months ago
I think the answer is Option A.
upvoted 0 times
...
Kris
12 months ago
I'm not sure, but Option C looks like it might be the right choice since it sets the port speed and duplex to match the 29301 device.
upvoted 0 times
Verona
8 months ago
But have you checked the other options?
upvoted 0 times
...
Buck
9 months ago
I think Option C makes sense too.
upvoted 0 times
...
Catarina
9 months ago
I feel like Option A could work as well.
upvoted 0 times
...
Luisa
9 months ago
Yeah, matching speed and duplex is crucial.
upvoted 0 times
...
...
Annmarie
1 year ago
The answer is clearly Option B. The interface configuration on the 29301 device shows it is using 1000BASE-T, so the corresponding configuration on the HPE Aruba switch port would be to use auto-negotiation.
upvoted 0 times
Brice
12 months ago
I agree, the 29301 device is using 1000BASE-T, so auto-negotiation would be the corresponding configuration.
upvoted 0 times
...
Virgie
12 months ago
I think the answer is Option B.
upvoted 0 times
...
...

Save Cancel