Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

HPE7-A01 Exam - Topic 7 Question 8 Discussion

With the Aruba CX 6100 48G switch with uplinks of 1/1/47 and 1/1/48. how do you automate the process of resuming the port operational state once a loop on a client port is cleared?
C) Configure int 1/1/1-1/1/46 loop-protect re-enable-timer.
A) Configure int 1/1/1-1/1/52 loop-protect disable timer.
B) Configure global loop-protect disable timer.
D) Configure global loop-protect re-enable-timer.

HPE7-A01 Exam - Topic 7 Question 8 Discussion

Actual exam question for HP's HPE7-A01 exam
Question #: 8
Topic #: 7
[All HPE7-A01 Questions]

With the Aruba CX 6100 48G switch with uplinks of 1/1/47 and 1/1/48. how do you automate the process of resuming the port operational state once a loop on a client port is cleared?

Show Suggested Answer Hide Answer
Suggested Answer: C

Loop protection is a feature that detects and prevents loops in layer 2 networks. Loop protection can be enabled on ports, LAGs, or VLANs. When loop protection is enabled, the switch sends periodic loop protection messages on the interface and expects to receive them back.If a loop protection message is received back on the same interface, it indicates a loop and the switch takes an action to disable the interface or block traffic on it3. The loop-protect re-enable-timer command is used to configure the length of time the switch waits before re-enabling an interface that was disabled due to loop detection.The default value is 0, which means that the interface remains disabled until manually re-enabled3.To automate the process of resuming the port operational state once a loop on a client port is cleared, the loop-protect re-enable-timer command can be used with a non-zero value on the interface range that includes the client ports3. Therefore, answer C is correct.


by Chauncey at Dec 10, 2023, 10:53 AM

Limited Time Offer

25%

Off

Get Premium HPE7-A01 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Lajuana
8 months ago
Really? I thought we had to disable it first before re-enabling.
upvoted 0 times
...
Whitney
8 months ago
I heard loop-protect can be tricky, but D seems solid.
upvoted 0 times
...
Denae
8 months ago
Wait, isn't option C better for specific ports?
upvoted 0 times
...
Winifred
9 months ago
Definitely agree with that! Global timers make sense.
upvoted 0 times
...
Maryann
9 months ago
I think option D is the way to go for global settings.
upvoted 0 times
...
Amalia
9 months ago
I vaguely remember that the re-enable timer is crucial for resuming port operation, but I can't remember if it should be set globally or per interface.
upvoted 0 times
...
Milly
9 months ago
I feel like the global settings are usually more effective, but I can't recall if that's the right approach for this specific switch model.
upvoted 0 times
...
Kayleigh
9 months ago
I think we practiced a similar question where we had to set a re-enable timer for loop protection. Could it be option D?
upvoted 0 times
...
Camellia
10 months ago
I remember something about loop protection, but I'm not sure if it's the global or interface-specific settings we need to focus on here.
upvoted 0 times
...
Vicky
10 months ago
Ah, I've seen this type of question before. The key is to configure the right timer, either globally or for the specific ports. I think I've got this one figured out, but I'll double-check my work just to be sure.
upvoted 0 times
...
Mauricio
10 months ago
Whoa, this is a new one for me. I'm not too familiar with the loop-protect feature and how to automate the port state resumption. I'll need to do some quick research to make sure I understand the concepts before selecting an answer.
upvoted 0 times
...
Shawn
10 months ago
Alright, this is a good test of my Aruba CX switch knowledge. I'm pretty confident I can identify the right solution here, but I'll make sure to read the question and options thoroughly.
upvoted 0 times
...
Andra
10 months ago
Okay, let me see here. I think the key is to find the right timer configuration, either globally or just for the specific ports. I'll need to double-check the syntax, but I think I can figure this out.
upvoted 0 times
...
Irene
10 months ago
Hmm, this looks like a tricky one. I'll need to carefully read through the options and think about the specific configuration required to automate the port state resumption.
upvoted 0 times
...
Armanda
10 months ago
Okay, I think I've got this. I'll just need to find the 'Try Research' text on the slide and insert the hyperlink. Shouldn't be too hard.
upvoted 0 times
...
Celeste
10 months ago
I thought global variables could be changed easily, but I can't recall if there are restrictions like option D suggests.
upvoted 0 times
...

Save Cancel