Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Hitachi Vantara HQT-4180 Exam - Topic 2 Question 11 Discussion

You need to replace a broken disk drive on a VSP G700.What are two prerequisites? (Choose two.)
A) You must use the Replace button in the Maintenance Utility before removing the drive. and B) You must wear a wrist strap for ESD protection.
C) The red LED on the drive must be lit.
D) The Drive Box where the drive is located must be powered down.

Hitachi Vantara HQT-4180 Exam - Topic 2 Question 11 Discussion

Actual exam question for Hitachi Vantara's HQT-4180 exam
Question #: 11
Topic #: 2
[All HQT-4180 Questions]

You need to replace a broken disk drive on a VSP G700.

What are two prerequisites? (Choose two.)

Show Suggested Answer Hide Answer
Suggested Answer: A, B

by Ruthann at Mar 25, 2023, 12:04 PM

Limited Time Offer

25%

Off

Get Premium HQT-4180 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Huey
8 months ago
I thought you could just swap drives without all this prep!
upvoted 0 times
...
Dyan
8 months ago
The red LED being lit is just a safety check, right?
upvoted 0 times
...
Hermila
9 months ago
Wait, do you really have to power down the Drive Box?
upvoted 0 times
...
Marsha
9 months ago
Agreed, ESD protection is a must!
upvoted 0 times
...
Victor
9 months ago
You definitely need to use the Replace button first!
upvoted 0 times
...
Terry
9 months ago
I practiced a similar question, and I’m pretty sure the Drive Box needs to be powered down before we can replace the drive.
upvoted 0 times
...
Dierdre
9 months ago
I’m a bit confused; I thought the red LED had to be lit, but I can't recall if that's a requirement or just a status indicator.
upvoted 0 times
...
Whitney
9 months ago
I remember something about ESD protection, so wearing a wrist strap seems like a good choice.
upvoted 0 times
...
Flo
9 months ago
I think we definitely need to use the Replace button in the Maintenance Utility before removing the drive, but I'm not sure about the second one.
upvoted 0 times
...
Mayra
9 months ago
I practiced a similar question, and I think powering down the Drive Box is crucial before replacing the drive.
upvoted 0 times
...
Javier
9 months ago
I feel like the red LED on the drive being lit is important, but I can't recall if it's a prerequisite or just a good indicator.
upvoted 0 times
...
Rose
9 months ago
I'm not entirely sure, but I remember something about needing to wear a wrist strap for ESD protection. Is that right?
upvoted 0 times
...
Rosendo
9 months ago
I think we definitely need to use the Replace button in the Maintenance Utility before removing the drive. That sounds familiar.
upvoted 0 times
...
Chuck
9 months ago
The error mentions an "Unknown device 0a.00.99", so I'm thinking the cable connected to controller A's 0a port might be the problem. I'll start there.
upvoted 0 times
...
Delisa
9 months ago
The Dev Hub is definitely the right answer here. That's the Salesforce feature that allows you to create and manage scratch orgs as part of your development process.
upvoted 0 times
...
Jaime
10 months ago
I think OSPF is one of the protocols supported, but I'm a bit shaky on the second one. Could it be EIGRP?
upvoted 0 times
...

Save Cancel