Dell EMC Exam D-RP-DY-A-24 Topic 6 Question 29 Discussion

Actual exam question for Dell EMC's D-RP-DY-A-24 exam

Question #: 29
Topic #: 6

You completed creating the RecoverPoint zoning on the SAN switch based on the design document. What is the zoning method that should be used while running the

RecoverPoint with VNX(SE) Installation wizard?

AAutomatic

BManual

CDual initiator zoning

DSemi-automatic

Show Suggested Answer

Suggested Answer: B

When configuring zoning for RecoverPoint with VNX(SE), it is essential to follow the best practices and guidelines provided by Dell.

The zoning configuration typically involves manual setup to ensure that the RPA ports and VNX Front End (FE) ports are correctly zoned to allow for proper communication and replication processes1.

The manual method allows for precise control over the zoning configuration, which is crucial for the RecoverPoint system's performance and reliability1.

While automatic zoning might be available in some environments, the recommended and supported method for RecoverPoint with VNX(SE) is manual zoning, as it provides the necessary customization and adherence to best practices1.

For the most accurate and detailed instructions, always refer to the latest official documentation or contact Dell EMC support directly. The information provided here is based on general knowledge of RecoverPoint systems and may not reflect the most recent updates or specific configurations.

by Josephine at Aug 04, 2025, 10:59 PM

Limited Time Offer

25%

Off

Get Premium D-RP-DY-A-24 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Margurite

3 days ago

I practiced a similar question, and I feel like Manual zoning was mentioned as a more controlled option.

upvoted 0 times

...

Tamera

9 days ago

I think the zoning method should be Automatic, but I'm not entirely sure. I remember something about it being easier for setup.

upvoted 0 times

...

Jolanda

14 days ago

The key here is that the question is asking about the zoning method to use while running the wizard. That makes me think Semi-automatic is probably the right approach, but I'll double-check the options to be sure.

upvoted 0 times

...

Frederick

20 days ago

Automatic zoning would be my first guess, since the wizard is involved. But I'm not 100% sure, so I'll review the design document details again before answering.

upvoted 0 times

...

Lai

25 days ago

Hmm, I'm a bit confused. The question mentions the RecoverPoint with VNX(SE) Installation wizard, so I'm not sure if Manual is the right answer. I'll have to think this through carefully.

upvoted 0 times

...

Chau

1 months ago

This question seems pretty straightforward. I think the zoning method should be Manual based on the information provided.

upvoted 0 times

...

Erasmo

1 months ago

If they wanted us to use the 'Wizard', they should have just called it the 'Wand'. Accio correct answer!

upvoted 0 times

...

Tiffiny

2 months ago

Hmm, I'm gonna go with D. Semi-automatic. Sounds like a good compromise between control and convenience.

upvoted 0 times

...

Bo

3 months ago

Automatic zoning? Really? That's just asking for trouble. Gotta go with the manual option, B, to make sure it's done right.

upvoted 0 times

Shawnda

2 months ago

I agree, manual zoning is the way to go to ensure everything is set up correctly.

upvoted 0 times

...

Trina

3 months ago

I think the correct answer is C. Dual initiator zoning. It's the only option that makes sense for RecoverPoint with VNX(SE).

upvoted 0 times

Kimberlie

2 months ago

I think the correct answer is C. Dual initiator zoning. It's the only option that makes sense for RecoverPoint with VNX(SE).

upvoted 0 times

...