Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 350-501 Exam - Topic 16 Question 86 Discussion

Refer to the exihibit.Refer to the exhibit. A network engineer is implementing iBGP and eBGP between AS 600 and AS 500 with these requirements:R2 must establish eBGP peering on 192.168.3.0/30 with R5 for sending unicast and multicast trafficR2 must wait for 30 seconds before sending BGP updates to R5 for multicast traffic.Which action must be taken on R2 to meet the requirements?
B) Configure advertisement-Interval 30 in address-family Ipv4 multicast
A) Configure advertisement-interval 30 In address-family ipv4 unicast
C) Apply timers bgp 30 in address-family ipv4 unicast
D) Apply timers bgp 30 in address-family ipv4 multicast.

Cisco 350-501 Exam - Topic 16 Question 86 Discussion

Actual exam question for Cisco's 350-501 exam
Question #: 86
Topic #: 16
[All 350-501 Questions]

Refer to the exihibit.

Refer to the exhibit. A network engineer is implementing iBGP and eBGP between AS 600 and AS 500 with these requirements:

R2 must establish eBGP peering on 192.168.3.0/30 with R5 for sending unicast and multicast traffic

R2 must wait for 30 seconds before sending BGP updates to R5 for multicast traffic.

Which action must be taken on R2 to meet the requirements?

Show Suggested Answer Hide Answer
Suggested Answer: B

The requirement is for R2 to delay sending BGP updates to R5 for multicast traffic by 30 seconds. This can be achieved by configuring the advertisement interval for IPv4 multicast traffic on R2, which controls the frequency of sending BGP updates for multicast routes.Reference:=Cisco SPCOR


by Huey at Apr 26, 2024, 02:39 PM

Limited Time Offer

25%

Off

Get Premium 350-501 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Alpha
9 months ago
Just to clarify, R2 needs to wait 30 seconds for multicast, right?
upvoted 0 times
...
Charlene
9 months ago
I think D could also work, but B feels safer.
upvoted 0 times
...
Elza
10 months ago
Wait, are we sure about that? Seems tricky.
upvoted 0 times
...
Madonna
10 months ago
Definitely agree with that, B is the right choice.
upvoted 0 times
...
Edelmira
10 months ago
Gotta go with option B for multicast updates!
upvoted 0 times
...
Flo
10 months ago
I feel like I might have seen something about advertisement-interval in the context of unicast before. Could it be option A?
upvoted 0 times
...
Pansy
11 months ago
I’m a bit confused about the difference between unicast and multicast settings here. Was it advertisement-interval or timers we needed to adjust?
upvoted 0 times
...
Tracie
11 months ago
I remember practicing a similar question where we had to set timers for BGP updates. I feel like option D makes the most sense for multicast.
upvoted 0 times
...
Basilia
11 months ago
I think we need to configure the advertisement-interval for multicast, but I'm not sure if it's option B or D.
upvoted 0 times
...
Raylene
11 months ago
I've got this! The requirements clearly state that I need to set a 30-second delay for multicast traffic updates, so I'll use the "advertisement-interval 30" command in the ipv4 multicast address-family.
upvoted 0 times
...
Thad
11 months ago
Wait, I'm a bit confused. Do I need to use the "timers bgp" command instead of "advertisement-interval"? I'll have to double-check the syntax for each option.
upvoted 0 times
...
Georgene
11 months ago
Okay, the key things I need to focus on are setting the advertisement interval for unicast and multicast traffic separately. I think I'll need to use the "advertisement-interval" command for that.
upvoted 0 times
...
Herminia
11 months ago
Hmm, this looks like a tricky BGP configuration question. I'll need to carefully read through the requirements and think about the appropriate BGP commands to use.
upvoted 0 times
...
Noelia
11 months ago
Hmm, scope definition... I remember that involves things like stakeholder analysis and defining project assumptions. But I'm not certain if change requests would be considered a tool for that. I'll have to think this through more carefully.
upvoted 0 times
...
Paris
11 months ago
Okay, let me break this down. Direct and Manage Project Execution is about performing the planned activities, not just integrating them or developing the plan. I think I've got this.
upvoted 0 times
...
Kirk
11 months ago
I practiced a similar question, but I can't recall the exact details. Moving the contract to a new blockchain doesn't seem right to me, though.
upvoted 0 times
...
Ollie
2 years ago
I also went with B. Address-family ipv4 multicast plus the interval specified.
upvoted 0 times
...
Viola
2 years ago
Yeah, but timers bgp 30 sounds wrong. Advertisement-interval is more appropriate.
upvoted 0 times
...
Emerson
2 years ago
Multicast traffic, right? Needs waiting period of 30 seconds.
upvoted 0 times
...
Lorenza
2 years ago
Why B? I think D makes more sense.
upvoted 0 times
...
Emerson
2 years ago
I think it's B.
upvoted 0 times
...
Ollie
2 years ago
This question is tricky. What did you choose?
upvoted 0 times
...

Save Cancel