Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 350-501 Exam - Topic 14 Question 66 Discussion

The service provider is serving hosts with two different multicast streams from source X and source Y. Source X is multicast group 224.0.0.0/8, and source Y is multicast group 226.0.0.0/8. Multicast source X should send its stream through bidirectional RP address 10.20.1.1, and multicast source Y should send its stream through RP address 10.20.2.1. Which configuration meets these requirements?
B) Add ip pim bidir-enable in global mode on RB.
A) Enable ip pim ssm default on RA and RB.
C) Permit the source X and source Y IP addresses in the access list on RB.
D) Set PIM sparse mode with a static RP address of 10.20.2.1 on RA and RC.

Cisco 350-501 Exam - Topic 14 Question 66 Discussion

Actual exam question for Cisco's 350-501 exam
Question #: 66
Topic #: 14
[All 350-501 Questions]

The service provider is serving hosts with two different multicast streams from source X and source Y. Source X is multicast group 224.0.0.0/8, and source Y is multicast group 226.0.0.0/8. Multicast source X should send its stream through bidirectional RP address 10.20.1.1, and multicast source Y should send its stream through RP address 10.20.2.1. Which configuration meets these requirements?

Show Suggested Answer Hide Answer
Suggested Answer: B

by Aja at Feb 25, 2023, 02:05 PM

Limited Time Offer

25%

Off

Get Premium 350-501 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Precious
10 months ago
Isn't 10.20.1.1 the right RP for source X? Just checking!
upvoted 0 times
...
Man
10 months ago
I think option C is crucial for allowing those sources.
upvoted 0 times
...
Annett
10 months ago
Wait, why are we using two different RPs? Seems odd.
upvoted 0 times
...
An
11 months ago
Totally agree, option B seems like the way to go!
upvoted 0 times
...
Johana
11 months ago
Source X is in the 224.0.0.0/8 range, right?
upvoted 0 times
...
Harrison
11 months ago
I’m a bit confused about the access list in option C. I thought it was more about routing than just permitting IP addresses.
upvoted 0 times
...
Johnna
11 months ago
I practiced a similar question where we had to configure multicast streams, and I feel like option D might be too restrictive since it only mentions one RP.
upvoted 0 times
...
Beula
11 months ago
I think enabling ip pim ssm default could be relevant, but it feels like it might not address the RP requirements for both sources.
upvoted 0 times
...
Gerri
11 months ago
I remember we discussed the importance of using the correct RP for bidirectional PIM, but I'm not sure if option B is the right choice here.
upvoted 0 times
...
Virgilio
11 months ago
This is a tricky one. I'll need to review the WSDL structure and think through how the portType and binding elements should be defined for a Time service. I'll take my time and try to eliminate the incorrect options.
upvoted 0 times
...
Denna
11 months ago
This is a tricky one. I'm a bit confused about the use of the parentheses and the ampersand in the options. I'll have to review my notes on DTD attribute list declarations to make sure I understand the proper syntax before selecting an answer.
upvoted 0 times
...
Verona
11 months ago
I've seen this topic come up before, so I feel like I have a good handle on it. I'll just review the key points quickly.
upvoted 0 times
...

Save Cancel