Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 350-401 Exam - Topic 18 Question 80 Discussion

Refer to the Exhibit.An ertgineer must modify the existing configuration so that R2 can take over as the primary router when serial interface 0/0.1 on R1 goes down. Whtch command must the engineer apply''
A) R2W standby 100 track 26 decrement 10
B) R2# standby 100 preempt
C) R2# track 26 interface SerialWO.1 line-protocol
D) R2# standby 100 priority 100

Cisco 350-401 Exam - Topic 18 Question 80 Discussion

Actual exam question for Cisco's 350-401 exam
Question #: 80
Topic #: 18
[All 350-401 Questions]

Refer to the Exhibit.

An ertgineer must modify the existing configuration so that R2 can take over as the primary router when serial interface 0/0.1 on R1 goes down. Whtch command must the engineer apply''

Show Suggested Answer Hide Answer
Suggested Answer: A

by Bernardo at Feb 08, 2024, 07:15 PM

Limited Time Offer

25%

Off

Get Premium 350-401 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Meaghan
9 months ago
Wait, can R2 really take over that quickly? Sounds risky!
upvoted 0 times
...
Catarina
9 months ago
Command A looks interesting, but I don’t think it’s the main solution.
upvoted 0 times
...
Nakita
10 months ago
I’m not so sure about that, isn’t priority more important?
upvoted 0 times
...
Shelton
10 months ago
Definitely agree, preempt is key for failover!
upvoted 0 times
...
Brandee
10 months ago
I think the right command is B, preempt is crucial.
upvoted 0 times
...
Kristin
10 months ago
I’m leaning towards option B for preemption, but I also remember something about adjusting priority. This is tricky!
upvoted 0 times
...
Daisy
11 months ago
I feel like the command to track the interface is crucial here, but I can't recall if it's option C or something else.
upvoted 0 times
...
Yaeko
11 months ago
I remember practicing a similar question where we had to configure HSRP settings. I think "standby preempt" was important in that context.
upvoted 0 times
...
Antonio
11 months ago
I think the command for R2 to take over as primary might be related to preemption, but I'm not entirely sure which one it is.
upvoted 0 times
...
Daisy
11 months ago
I'm a bit confused by the wording of the question. I'll need to double-check the HSRP commands to make sure I understand which one is the right solution here.
upvoted 0 times
...
Amber
11 months ago
Okay, let me think this through. I know HSRP is used for router redundancy, so I'll need to look at the options and see which one sets up the backup router properly.
upvoted 0 times
...
Lindsay
11 months ago
Hmm, this looks like a HSRP configuration question. I'll need to review the HSRP commands and how to configure a backup router to take over when the primary goes down.
upvoted 0 times
...
Helga
11 months ago
Alright, I've got this. The key is to configure the standby priority and tracking on R2 to make it the backup router that takes over when the primary interface goes down.
upvoted 0 times
...
Britt
11 months ago
I feel pretty confident about this one. The passage clearly describes an issue with the cash basis of accounting, where loans are being treated as revenue instead of liabilities. I'll go with option A.
upvoted 0 times
...
Glory
11 months ago
I'm a bit confused on this one. Is the lifespan determined by the subprocess that the data object is part of, or is there some other factor at play? I'll need to review my notes on subprocess data objects to figure this out.
upvoted 0 times
...
Samira
2 years ago
I chose A) because it mentions tracking the interface and decrementing a priority
upvoted 0 times
...
Tamesha
2 years ago
I'm not sure, but I think it might be D)
upvoted 0 times
...
Julio
2 years ago
I disagree, I believe it is B)
upvoted 0 times
...
Samira
2 years ago
I think the answer is A)
upvoted 0 times
...
Robt
2 years ago
Yeah, I was thinking the same thing. Option B with the 'preempt' command seems more straightforward to me.
upvoted 0 times
Jules
2 years ago
Good idea, let's make sure R2 can take over seamlessly.
upvoted 0 times
...
Lavelle
2 years ago
Agreed, let's implement the preempt command on R2.
upvoted 0 times
...
Jose
2 years ago
Let's go with Option B then, it seems like the most efficient solution.
upvoted 0 times
...
Angelo
2 years ago
True, but using 'preempt' could prevent unnecessary delays.
upvoted 0 times
...
Yen
2 years ago
Wouldn't tracking interface status also be important for failover?
upvoted 0 times
...
Chaya
2 years ago
I agree, it ensures that R2 can take over immediately.
upvoted 0 times
...
Arminda
2 years ago
Option B with the 'preempt' command seems like the best choice.
upvoted 0 times
...
...
Jacklyn
2 years ago
Okay, let's think this through. Option A looks promising, but I'm not sure about the 'decrement 10' part. That might be a bit excessive.
upvoted 0 times
...
Vallie
2 years ago
I agree, this is a tricky one. We need to track the interface state to trigger the switchover when the link goes down.
upvoted 0 times
...
Georgene
2 years ago
Hmm, this question seems to be testing our understanding of HSRP (Hot Standby Router Protocol). We need to configure R2 to take over as the primary router when the serial interface 0/0.1 on R1 goes down.
upvoted 0 times
...

Save Cancel