Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-710 Exam - Topic 8 Question 86 Discussion

Which Cisco Firepower Threat Defense, which two interface settings are required when configuring a routed interface? (Choose two.)
B) EtherChannel
A) Redundant Interface
C) Speed
D) Media Type
E) Duplex

Cisco 300-710 Exam - Topic 8 Question 86 Discussion

Actual exam question for Cisco's 300-710 exam
Question #: 86
Topic #: 8
[All 300-710 Questions]

Which Cisco Firepower Threat Defense, which two interface settings are required when configuring a routed interface? (Choose two.)

Show Suggested Answer Hide Answer
Suggested Answer: B

To deploy a Cisco FTD device that meets the requirements of the question, the engineer must use transparent mode with a management interface. Transparent mode is a firewall configuration in which the FTD device acts as a ''bump in the wire'' or a ''stealth firewall'' and is not seen as a router hop to connected devices.In transparent mode, the FTD device can examine traffic without requiring network changes that will disrupt end users, such as changing IP addresses or routing configurations1. A management interface is a dedicated interface that is used for managing the FTD device and separating management traffic from data traffic.A management interface can be configured to allow SSH access for remote administration, which is more secure than Telnet2.

The other options are incorrect because:

Routed mode is a firewall configuration in which the FTD device acts as a router and performs address translation and routing for connected networks.Routed mode requires network changes that may disrupt end users, such as changing IP addresses or routing configurations1. A diagnostic interface is a special interface that is used for troubleshooting and capturing traffic on the FTD device. A diagnostic interface does not separate management traffic from data traffic or allow SSH access for remote administration.

Transparent mode with a data interface does not meet the requirement of separating management traffic from data traffic. A data interface is a regular interface that is used for passing and inspecting traffic on the FTD device.A data interface does not allow SSH access for remote administration2.

Routed mode with a bridge virtual interface (BVI) does not meet the requirement of examining traffic without requiring network changes that will disrupt end users. A BVI is a logical interface that acts as a container for one or more physical or logical interfaces that belong to the same layer 2 broadcast domain. A BVI allows the FTD device to route between different bridge groups on the same security module/engine. However, routed mode still requires network changes that may disrupt end users, such as changing IP addresses or routing configurations.


by Jovita at May 07, 2024, 03:42 PM

Limited Time Offer

25%

Off

Get Premium 300-710 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Jacki
9 months ago
I thought you only needed Speed and Duplex, this is new info!
upvoted 0 times
...
Sanda
9 months ago
Media Type is also important, right?
upvoted 0 times
...
Alica
10 months ago
Wait, are Redundant Interface and EtherChannel not required?
upvoted 0 times
...
Shannon
10 months ago
Totally agree, those are essential!
upvoted 0 times
...
Chauncey
10 months ago
You need Speed and Duplex settings for routed interfaces.
upvoted 0 times
...
Weldon
10 months ago
I’m leaning towards Speed and Duplex as the correct answers, but I might be mixing it up with other interface configurations we studied.
upvoted 0 times
...
Cristal
11 months ago
I’m a bit confused about the Redundant Interface option. I don’t recall it being necessary for a basic routed interface setup.
upvoted 0 times
...
Corazon
11 months ago
I feel like I saw a similar question in our practice tests, and I think Media Type was mentioned as a requirement too.
upvoted 0 times
...
Clorinda
11 months ago
I think I remember that Speed and Duplex settings are important for a routed interface, but I'm not entirely sure if both are required.
upvoted 0 times
...
Erasmo
11 months ago
I think the answer is Speed and Duplex. Those are the fundamental settings you need to configure for any routed interface on a Cisco Firepower Threat Defense device.
upvoted 0 times
...
Karol
11 months ago
Okay, I've got this. The two required settings are Speed and Media Type. Routed interfaces need to have the correct speed and media type configured to function properly on the network.
upvoted 0 times
...
Vilma
11 months ago
Hmm, I'm a bit confused on this one. I know we need to configure the interface, but I'm not sure if Redundant Interface or EtherChannel are required for a routed interface. Let me think this through carefully.
upvoted 0 times
...
Gail
11 months ago
I'm pretty sure the two required interface settings are Speed and Duplex, since those are the basic network interface configuration parameters.
upvoted 0 times
...
Gerardo
11 months ago
This looks like a pretty straightforward question about integrating Salesforce with an external system. I think I'll go with option B - using the SOAP API to maintain the related SObject_share records. That seems like the most direct way to control record access.
upvoted 0 times
...
Milly
11 months ago
Okay, let's see. If the measure is risk-adjusted, the comparative norm is the predicted rate. If it's not risk-adjusted, it's the comparison group mean. I think I've got that right.
upvoted 0 times
...
Viola
11 months ago
Hmm, I'm not sure. A heuristic review might also work to evaluate the feature's usability and alignment with design best practices. That could provide some valuable insights.
upvoted 0 times
...
Keneth
1 year ago
Wait, are we supposed to pick the two options that make the firewall go 'pew pew'? I'm just here for the lasers, man.
upvoted 0 times
...
Elmira
1 year ago
I'm feeling confident with A and E. Redundant Interface and Duplex, that's the secret sauce for a rock-solid Firepower setup.
upvoted 0 times
Madalyn
1 year ago
It's great that you're confident in your choices, those settings will definitely help with your Firepower configuration.
upvoted 0 times
...
Stevie
1 year ago
Make sure to double check those settings before finalizing the configuration.
upvoted 0 times
...
Jenelle
1 year ago
Definitely, setting the correct duplex mode is also important for optimal performance.
upvoted 0 times
...
Annelle
1 year ago
Definitely, setting the correct duplex mode is key for optimal performance.
upvoted 0 times
...
Benton
1 year ago
I agree, having a redundant interface is crucial for failover.
upvoted 0 times
...
Annalee
1 year ago
I agree, having a redundant interface is crucial for failover.
upvoted 0 times
...
...
Erin
1 year ago
C and D, for sure. Speed and Media Type, that's where it's at! Gotta keep those packets moving at lightning speed, you know?
upvoted 0 times
Frederica
1 year ago
EtherChannel can help increase bandwidth and provide redundancy as well.
upvoted 0 times
...
Candida
1 year ago
Redundant interface is also necessary for backup in case of failure.
upvoted 0 times
...
Glory
1 year ago
Yeah, media type is crucial too. Can't have any compatibility issues.
upvoted 0 times
...
Helene
1 year ago
I agree, speed is definitely important for a routed interface.
upvoted 0 times
...
Chara
1 year ago
Agreed, those settings are crucial for keeping the network running smoothly. Can't afford any slowdowns.
upvoted 0 times
...
Lynelle
1 year ago
C and D are definitely important for configuring a routed interface. Speed and Media Type are key!
upvoted 0 times
...
...
Adria
1 year ago
I'm not sure about that, I think EtherChannel and Media Type are also important for configuring a routed interface.
upvoted 0 times
...
Earleen
1 year ago
I agree with Jamal, Speed and Duplex are definitely required for configuring a routed interface.
upvoted 0 times
...
Joanne
1 year ago
Hmm, I'm going with B and E. EtherChannel and Duplex, those are the ones that really make the network sing, am I right?
upvoted 0 times
...
Jamal
1 year ago
I think the required interface settings are Speed and Duplex.
upvoted 0 times
...
Delila
1 year ago
I'm not sure about Speed and Duplex, I think it might be Redundant Interface and EtherChannel.
upvoted 0 times
...
Reynalda
1 year ago
I agree with Geraldo, Speed and Duplex are definitely required for configuring a routed interface.
upvoted 0 times
...
Lachelle
1 year ago
C and E, easy peasy! Gotta love those speed and duplex settings, they're the real deal when it comes to Firepower Threat Defense!
upvoted 0 times
King
1 year ago
Definitely, the devil is in the details when it comes to network security.
upvoted 0 times
...
Rodolfo
1 year ago
I agree, it's important to pay attention to the details when setting up Firepower Threat Defense.
upvoted 0 times
...
Ettie
1 year ago
Yeah, those settings are crucial for optimizing network performance.
upvoted 0 times
...
Theodora
1 year ago
I always make sure to configure the speed and duplex settings on my routed interfaces.
upvoted 0 times
...
...
Geraldo
1 year ago
I think the required interface settings are Speed and Duplex.
upvoted 0 times
...

Save Cancel