Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-710 Exam - Topic 7 Question 54 Discussion

An administrator is attempting to add a new FTD device to their FMC behind a NAT device with a NAT ID of NAT001 and a password of Cisco0420l06525. The private IP address of the FMC server is 192.168.45.45. which is being translated to the public IP address of 209.165.200.225/27. Which command set must be used in order to accomplish this task?
A) configure manager add 209.165.200.225 <reg_key> <nat_id>
B) configure manager add 192.168.45,45 <reg_key> <nat_id>
C) configure manager add 209.165.200.225 255.255.255.224 <reg_key> <nat_id>
D) configure manager add 209.165.200.225/27 <reg_key> <nat_id>

Cisco 300-710 Exam - Topic 7 Question 54 Discussion

Actual exam question for Cisco's 300-710 exam
Question #: 54
Topic #: 7
[All 300-710 Questions]

An administrator is attempting to add a new FTD device to their FMC behind a NAT device with a NAT ID of NAT001 and a password of Cisco0420l06525. The private IP address of the FMC server is 192.168.45.45. which is being translated to the public IP address of 209.165.200.225/27. Which command set must be used in order to accomplish this task?

Show Suggested Answer Hide Answer
Suggested Answer: A

by Kristel at Jul 24, 2022, 02:59 PM

Limited Time Offer

25%

Off

Get Premium 300-710 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Marlon
10 months ago
I agree with A, but I’m not sure about the reg_key part.
upvoted 0 times
...
Brinda
10 months ago
Wait, is the NAT ID really just NAT001? Seems too simple!
upvoted 0 times
...
Mitzie
10 months ago
I think option D is actually correct, not A.
upvoted 0 times
...
Darnell
11 months ago
Definitely option A! That’s the right command.
upvoted 0 times
...
Halina
11 months ago
The private IP is 192.168.45.45, so we need the public IP.
upvoted 0 times
...
Lashon
11 months ago
I’m leaning towards option D because it includes the subnet mask, which seems important for NAT configurations.
upvoted 0 times
...
Novella
11 months ago
I feel like we did a similar question where we had to specify the NAT ID. I think option A sounds right, but I’m not completely confident.
upvoted 0 times
...
Angella
11 months ago
I think it’s definitely the public IP since it’s behind NAT, but I can’t recall if the command needs the subnet mask included or not.
upvoted 0 times
...
Taryn
11 months ago
I remember we practiced adding FTD devices, but I’m not sure if the command should use the public or private IP.
upvoted 0 times
...
Lavonne
11 months ago
I'm a bit confused by this question. Wouldn't maximizing aisle width just be a part of maximizing flexibility in the warehouse layout? I'm not sure if those should be considered separate solutions. I'll need to re-read the question and options more carefully.
upvoted 0 times
...
Hildegarde
11 months ago
Hmm, I'm a bit unsure about this one. The diagram shows R1 connected to R2 and R3, but I'm not sure if those are iBGP or eBGP sessions. I'll have to think it through step-by-step.
upvoted 0 times
...

Save Cancel