Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-615 Exam - Topic 9 Question 120 Discussion

Refer to the exhibit.After a failover occurs, which two actions must be performed on Switch-B to manually preempt the operational main role back to Switch-A? (Choose two.)
B) Configure the local vPC role priority to have a higher value than Switch-A. and E) Disable and then re-enable the vPC peer link.
C) Disable and then re-enable the vPC peer-keepalive link.
D) Configure the local vPC role priority to have the same value as Switch-A.
A) Configure the local vPC role priority to have a lower value than Switch-A.

Cisco 300-615 Exam - Topic 9 Question 120 Discussion

Actual exam question for Cisco's 300-615 exam
Question #: 120
Topic #: 9
[All 300-615 Questions]

Refer to the exhibit.

After a failover occurs, which two actions must be performed on Switch-B to manually preempt the operational main role back to Switch-A? (Choose two.)

Show Suggested Answer Hide Answer
Suggested Answer: B, E

by Colene at Jan 27, 2026, 04:13 PM

Limited Time Offer

25%

Off

Get Premium 300-615 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
German
2 months ago
Agreed! It’s all about ensuring Switch-A takes over smoothly.
upvoted 0 times
...
Chan
2 months ago
And don’t forget to reset the role on Switch-B. That’s crucial!
upvoted 0 times
...
Corinne
2 months ago
Definitely! I’d say we should configure the priority on Switch-A.
upvoted 0 times
...
Ashley
2 months ago
I think it's tricky. Need to check the configurations first.
upvoted 0 times
...
Annice
4 months ago
Just set the priority higher on Switch-A, right?
upvoted 0 times
...
Edna
4 months ago
I thought it was more complicated than that!
upvoted 0 times
...
Carmen
4 months ago
Wait, is it really that simple?
upvoted 0 times
...
Serina
4 months ago
Totally agree, and don’t forget to enable preemption!
upvoted 0 times
...
Roslyn
5 months ago
You need to configure the priority on Switch-B.
upvoted 0 times
...
Brittni
5 months ago
Wait, do I also need to reboot Switch-B? I'm not sure about that one.
upvoted 0 times
...
Sharita
5 months ago
Disabling and re-enabling the VRRP group sounds like the way to go.
upvoted 0 times
...
Rosio
5 months ago
Haha, I bet the exam writers are having a field day with these VRRP questions!
upvoted 0 times
...
Carisa
5 months ago
I think you also need to clear the VRRP statistics on Switch-B.
upvoted 0 times
...
Vince
5 months ago
The correct answer is to disable and then re-enable the VRRP group on Switch-B.
upvoted 0 times
...
Felix
6 months ago
I believe we have to manually set the role back to Switch-A, but I’m confused about whether we need to reboot Switch-B or not.
upvoted 0 times
...
Alesia
6 months ago
This reminds me of a practice question where we had to adjust the configuration settings after a failover. I think we might need to check the spanning tree settings too.
upvoted 0 times
...
Brett
7 months ago
I remember something about issuing a command to force the switch to relinquish the role, but I can't recall the specific syntax.
upvoted 0 times
...
Inocencia
7 months ago
I think we need to configure the priority on Switch-B to be lower than Switch-A, but I'm not entirely sure about the exact commands.
upvoted 0 times
...
Dana
7 months ago
This seems straightforward. I just need to remember the key steps to manually transition the main role back to Switch-A.
upvoted 0 times
...
Regenia
7 months ago
Based on the exhibit, I believe the two actions are to manually configure the port priority and then trigger a failover. Let me write that down.
upvoted 0 times
...
Alida
7 months ago
I'm a bit confused by this question. What exactly do they mean by "preempt the operational main role"?
upvoted 0 times
...
Salome
7 months ago
Okay, I think I know the answer here. Let me double-check the options.
upvoted 0 times
...
Nelida
8 months ago
Hmm, this looks like a tricky one. I'll need to carefully review the exhibit and think through the steps.
upvoted 0 times
Carrol
1 month ago
Don't forget to verify the configurations after!
upvoted 0 times
...
Earleen
1 month ago
Yeah, and then we should force the role back to Switch-A.
upvoted 0 times
...
Sage
2 months ago
I think we need to check the priority settings first.
upvoted 0 times
...
...

Save Cancel