Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-610 Exam - Topic 6 Question 119 Discussion

Refer to the exhibit A Cisco engineer is configuring Cisco Nexus 7000 Series Switches. To simplify initial configuration verification and vPC+/HSRP troubleshooting, the engineer configures the primary vPC+ peer device with the FHRP active router highest priority. The primary FHRP device responds to ARP requests, even though the secondary vPC+ device also forwards the data traffic. Which configuration enables the Layer 3 connectivity from each vPC* peer device?
B) Ensure that the enhanced Layer 2 license has been installed.
A) Configure a VLAN network interlace for the same VLAN from both devices.
C) Manually configure virtual MAC addresses tor any FHRP protocol.
D) Set a restore timer that delays the vPC+ restart.

Cisco 300-610 Exam - Topic 6 Question 119 Discussion

Actual exam question for Cisco's 300-610 exam
Question #: 119
Topic #: 6
[All 300-610 Questions]

Refer to the exhibit A Cisco engineer is configuring Cisco Nexus 7000 Series Switches. To simplify initial configuration verification and vPC+/HSRP troubleshooting, the engineer configures the primary vPC+ peer device with the FHRP active router highest priority. The primary FHRP device responds to ARP requests, even though the secondary vPC+ device also forwards the data traffic. Which configuration enables the Layer 3 connectivity from each vPC* peer device?

Show Suggested Answer Hide Answer
Suggested Answer: B

by Edgar at Jan 05, 2026, 05:16 AM

Limited Time Offer

25%

Off

Get Premium 300-610 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Melinda
4 months ago
I feel like option D is just a workaround. Better to fix the root issue with A or C.
upvoted 0 times
...
Maricela
4 months ago
Option B seems unnecessary. The license shouldn't affect basic connectivity.
upvoted 0 times
...
Merlyn
4 months ago
I agree, but option C could also work. Virtual MAC addresses help with FHRP.
upvoted 0 times
...
Jin
4 months ago
I think option A is the best choice. VLAN interfaces are crucial for Layer 3 connectivity.
upvoted 0 times
...
An
5 months ago
C seems like overkill for this setup, not necessary.
upvoted 0 times
...
Sheron
5 months ago
Wait, can you really use virtual MAC addresses for FHRP? Sounds tricky!
upvoted 0 times
...
Charlena
5 months ago
B is important too, but not the main focus here.
upvoted 0 times
...
Miesha
5 months ago
Totally agree with A, that's the way to go!
upvoted 0 times
...
Corinne
5 months ago
A) Configure a VLAN network interface for the same VLAN from both devices.
upvoted 0 times
...
Lore
5 months ago
Wait, is this a Cisco exam or a stand-up comedy routine?
upvoted 0 times
...
Oretha
6 months ago
D) Set a restore timer that delays the vPC+ restart.
upvoted 0 times
...
Thomasena
6 months ago
B) Ensure that the enhanced Layer 2 license has been installed.
upvoted 0 times
...
Krissy
6 months ago
Hmm, I thought the answer was to just unplug one of the devices and see which one catches fire first.
upvoted 0 times
...
Salley
7 months ago
A) Configure a VLAN network interlace for the same VLAN from both devices.
upvoted 0 times
...
Kimberely
7 months ago
C) Manually configure virtual MAC addresses tor any FHRP protocol.
upvoted 0 times
...
Janae
7 months ago
Setting a restore timer sounds familiar, but I don't think it addresses the Layer 3 connectivity issue directly.
upvoted 0 times
...
Jacinta
7 months ago
I feel like the enhanced Layer 2 license is important, but I can't recall if it directly affects Layer 3 connectivity.
upvoted 0 times
...
Leanora
7 months ago
I think I saw a similar question about FHRP protocols in our practice exam. Could it be about manually configuring virtual MAC addresses?
upvoted 0 times
...
Mari
7 months ago
I remember discussing how vPC+ works, but I'm not entirely sure if configuring a VLAN interface is the right approach here.
upvoted 0 times
...
Naomi
8 months ago
Delaying the vPC+ restart with a restore timer? I'm not sure how that would help with the Layer 3 connectivity. Seems like a bit of a red herring.
upvoted 0 times
...
Laine
8 months ago
Manually configuring the virtual MAC addresses for the FHRP protocol sounds like a good strategy to ensure the primary device responds to ARP requests.
upvoted 0 times
...
Bobbie
8 months ago
I'm a bit confused by the mention of the enhanced Layer 2 license. Does that play a role in the solution, or is that just a distractor?
upvoted 0 times
...
Sharen
8 months ago
Okay, I think I've got this. The key is to configure the VLAN network interface on both devices to enable the Layer 3 connectivity, right?
upvoted 0 times
...
Franklyn
8 months ago
Hmm, this seems like a tricky one. I'll need to carefully review the options and think through the vPC+ and FHRP configuration requirements.
upvoted 0 times
Vincent
2 months ago
True, but if the VLANs aren't configured right, it won't matter.
upvoted 0 times
...
Estrella
2 months ago
Agreed, but what about option C? Virtual MAC addresses could be important too.
upvoted 0 times
...
Billye
2 months ago
I think option A makes the most sense. VLAN interfaces are crucial.
upvoted 0 times
...
...

Save Cancel