Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-510 Exam - Topic 4 Question 88 Discussion

Actual exam question for Cisco's 300-510 exam
Question #: 88
Topic #: 4
[All 300-510 Questions]

Refer to the exhibit.

A network engineer must enable segment routing between the three autonomous systems with these requirements:

* OSPF link-state data for area 0 routers must be distributed to the controller via BGP LS.

* EPE must be enabled on the egress node in AS 100.

* Routers must advertise peer node SIDs to the controller R1 via BGP LS.

Which configuration must the engineer apply?

A)

B)

C)

D)

Show Suggested Answer Hide Answer
Suggested Answer: C

by Felix at Jun 02, 2024, 07:14 AM

Limited Time Offer

25%

Off

Get Premium 300-510 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Denny
5 months ago
Are we sure this is the right approach? Seems complicated.
upvoted 0 times
...
Jamey
5 months ago
Wait, EPE on the egress node? That's a twist!
upvoted 0 times
...
Felix
5 months ago
Not convinced, I feel like Option B might be better.
upvoted 0 times
...
Jose
6 months ago
I think Option C looks solid for this setup.
upvoted 0 times
...
Antonio
6 months ago
OSPF link-state data needs BGP LS for sure.
upvoted 0 times
...
Krissy
6 months ago
I feel like option B might be the right choice since it mentions advertising peer node SIDs, but I’m not entirely confident. I need to review the segment routing concepts again.
upvoted 0 times
...
Odette
6 months ago
I’m a bit confused about the requirements for distributing OSPF data. I think it’s crucial for the controller, but I can’t recall which option addresses that clearly.
upvoted 0 times
...
Goldie
6 months ago
This question feels similar to one we practiced about BGP LS and OSPF. I think it might be option C, but I need to double-check the SID configurations.
upvoted 0 times
...
Buck
7 months ago
I remember we discussed enabling EPE on the egress node, but I'm not sure which option specifically shows that.
upvoted 0 times
...
Tish
7 months ago
I'm a bit confused by the different autonomous system requirements. I'll need to double-check my understanding of segment routing and BGP LS before selecting an answer.
upvoted 0 times
...
Tracey
7 months ago
Okay, I see the key points - OSPF link-state data distribution, EPE enablement, and peer node SID advertisement. I'm pretty confident I can identify the right configuration.
upvoted 0 times
...
Avery
7 months ago
Hmm, the requirements seem pretty specific. I'll need to analyze each option closely to see which one meets all the criteria.
upvoted 0 times
...
Zona
7 months ago
This looks like a tricky question, but I think I can break it down step-by-step. Let me review the requirements carefully.
upvoted 0 times
...
Shala
7 months ago
This is a good test of my knowledge on segment routing and BGP LS. I'll methodically evaluate each option against the stated requirements.
upvoted 0 times
...
Daron
7 months ago
Hmm, I'm a bit confused by the wording of the options. Let me re-read this a few times to make sure I understand.
upvoted 0 times
...
Martha
7 months ago
Hmm, I'm a bit unsure about this one. The options seem similar, but I think I can eliminate a couple based on my understanding of project management processes. Let me think this through step-by-step.
upvoted 0 times
...
Micaela
7 months ago
Hmm, this one's tricky. I'll need to think through the relationship between the yield curve and medium rates.
upvoted 0 times
...
Alana
12 months ago
I'm feeling a bit 'router-ic' about this question. Let's hope I don't 'mask' my way to the wrong answer!
upvoted 0 times
...
Novella
12 months ago
I'm going to go with Option B. It seems simpler and more straightforward than the other options.
upvoted 0 times
Noah
10 months ago
I'm not sure, but I would lean towards Option B as well.
upvoted 0 times
...
Leonie
11 months ago
I think Option A might also work, but Option B does seem more straightforward.
upvoted 0 times
...
Lizbeth
11 months ago
I agree, Option B looks like the best choice for this scenario.
upvoted 0 times
...
...
Jovita
12 months ago
Option C looks like the correct answer to me. It has all the necessary configurations for the given requirements.
upvoted 0 times
...
Joanne
1 year ago
Hmm, this question is tricky. I think I need to read the requirements carefully and analyze each option closely.
upvoted 0 times
Paz
11 months ago
User4: Let's analyze each option step by step to make sure we choose the right one.
upvoted 0 times
...
Augustine
12 months ago
User3: I think option A might be the correct configuration.
upvoted 0 times
...
Edelmira
12 months ago
User2: Yes, we need to pay attention to the requirements and compare them with each option.
upvoted 0 times
...
Dustin
12 months ago
User1: This question seems challenging.
upvoted 0 times
...
...
Annelle
1 year ago
Hmm, you might be right. Option C does seem to cover all the specified requirements.
upvoted 0 times
...
Quentin
1 year ago
I disagree, I believe Option C is the right choice because it meets all the requirements.
upvoted 0 times
...
Annelle
1 year ago
I think the correct configuration is Option A.
upvoted 0 times
...

Save Cancel