Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-430 Exam - Topic 3 Question 98 Discussion

Refer to the exhibit.A customer has implemented Cisco FlexConnect deployments with different WLANs around the globe and is opening a new branch in a different location. The engineer's task is to execute all the wireless configuration and to suggest how to configure the switch ports for new APs. Which configuration must the switching team use on the switch port?
A) trunk mode
B) access mode
C) single VLAN
D) multiple VLAN

Cisco 300-430 Exam - Topic 3 Question 98 Discussion

Actual exam question for Cisco's 300-430 exam
Question #: 98
Topic #: 3
[All 300-430 Questions]

Refer to the exhibit.

A customer has implemented Cisco FlexConnect deployments with different WLANs around the globe and is opening a new branch in a different location. The engineer's task is to execute all the wireless configuration and to suggest how to configure the switch ports for new APs. Which configuration must the switching team use on the switch port?

Show Suggested Answer Hide Answer
Suggested Answer: A

: For new Access Points (APs) in a Cisco FlexConnect deployment, switch ports should be configured in trunk mode. This allows the APs to handle traffic for multiple WLANs or SSIDs, each associated with different VLANs. Trunk mode enables the AP to tag traffic with the correct VLAN IDs as per its configuration.Reference: CCNP Enterprise Wireless Design ENWLSD 300-425 and Implementation ENWLSI 300-430 Official Cert Guide


by Penney at Apr 10, 2026, 01:41 PM

Limited Time Offer

25%

Off

Get Premium 300-430 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Olive
3 days ago
Yes, trunk mode supports all WLANs globally.
upvoted 0 times
...
Audry
8 days ago
I feel trunk mode is the best choice for new branches.
upvoted 0 times
...
Vanesa
13 days ago
True, but multiple VLANs are needed for scalability.
upvoted 0 times
...
Gladis
19 days ago
But access mode could work for single VLAN setups.
upvoted 0 times
...
Lorrine
24 days ago
Agreed, trunk mode is essential for FlexConnect.
upvoted 0 times
...
Refugia
29 days ago
I think it should be trunk mode. It allows multiple VLANs.
upvoted 0 times
...
Brandon
1 month ago
Not sure if trunk mode is necessary for all branches...
upvoted 0 times
...
Fannie
1 month ago
Trunk mode is the way to go, no doubt about it!
upvoted 0 times
...
Haydee
1 month ago
Surprised they didn't mention single VLAN as an option!
upvoted 0 times
...
Svetlana
2 months ago
I think access mode could work too, but not ideal.
upvoted 0 times
...
Reuben
2 months ago
Definitely trunk mode for multiple VLANs!
upvoted 0 times
...
German
2 months ago
Are we sure trunk mode is necessary for all locations?
upvoted 0 times
...
Jesusita
2 months ago
Trunk mode is the way to go, no doubt about it.
upvoted 0 times
...
Ashley
2 months ago
Surprised they didn't mention multiple VLANs!
upvoted 0 times
...
Merilyn
4 months ago
I think access mode could work too, but not ideal.
upvoted 0 times
...
Goldie
4 months ago
Definitely trunk mode for FlexConnect!
upvoted 0 times
...
Jillian
5 months ago
I’m a bit confused about whether single VLAN or multiple VLAN is better for FlexConnect; I should have reviewed that section more thoroughly.
upvoted 0 times
...
Nakita
5 months ago
This question seems similar to one we practiced where we had to configure switch ports for APs, and I think trunk mode was the answer there too.
upvoted 0 times
...
Frederica
5 months ago
I think access mode is typically for connecting a single device, but I feel like there might be exceptions for APs.
upvoted 0 times
...
Nickie
5 months ago
I remember something about trunk mode being used for multiple VLANs, but I'm not entirely sure if that's the right choice here.
upvoted 0 times
...

Save Cancel