Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-410 Exam - Topic 5 Question 112 Discussion

Refer to the exhibit.Refer to the exhibit. An administrator must harden a router, but the administrator failed to test the SSH access successfully to the router. Which action resolves the issue?
B) SSH syntax must be ssh -I user ip to log in to the remote device
A) Configure SSH on the remote device to log m using SSH
C) Configure enable secret to log in to the device
D) SSH must be allowed with the transport output ssh command

Cisco 300-410 Exam - Topic 5 Question 112 Discussion

Actual exam question for Cisco's 300-410 exam
Question #: 112
Topic #: 5
[All 300-410 Questions]

Refer to the exhibit.

Refer to the exhibit. An administrator must harden a router, but the administrator failed to test the SSH access successfully to the router. Which action resolves the issue?

Show Suggested Answer Hide Answer
Suggested Answer: B

by Kina at Jun 15, 2025, 07:19 PM

Limited Time Offer

25%

Off

Get Premium 300-410 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Lavera
8 months ago
Definitely need that enable secret configured too!
upvoted 0 times
...
Daryl
9 months ago
Wait, can you really just use ssh -I? Sounds off.
upvoted 0 times
...
Annmarie
9 months ago
SSH needs to be enabled on the router for access.
upvoted 0 times
...
Paul
9 months ago
I think option D is the right move here!
upvoted 0 times
...
Ryan
9 months ago
Not sure about that, but I thought SSH was already set up?
upvoted 0 times
...
Chauncey
9 months ago
I’m a bit confused about the SSH syntax; I thought it was just ssh user@ip, but maybe the -I option is necessary?
upvoted 0 times
...
Gail
10 months ago
I practiced a similar question where we had to troubleshoot SSH access, and I feel like configuring SSH on the remote device was key.
upvoted 0 times
...
Remedios
10 months ago
I think option D sounds familiar, but I also recall something about needing to set up the enable secret for secure access.
upvoted 0 times
...
Heike
10 months ago
I remember we discussed SSH configurations in class, but I'm not entirely sure if the transport output command is the right fix here.
upvoted 0 times
...
Lindy
10 months ago
This is a good test of my networking knowledge. I'll take my time and make sure I select the best solution.
upvoted 0 times
...
Lindsey
11 months ago
I'm pretty confident I know the right answer here. The key is understanding how to properly configure SSH on the router.
upvoted 0 times
...
Ty
11 months ago
Okay, I've got a strategy - I'll eliminate the options that don't seem relevant, then focus on the ones that address the issue of SSH access.
upvoted 0 times
...
Florencia
11 months ago
Hmm, I'm a bit confused by the wording here. I'll need to re-read the question and look closely at the exhibit.
upvoted 0 times
...
Otis
11 months ago
This one looks tricky, but I think I can figure it out. Let me review the options carefully.
upvoted 0 times
...
Andree
1 year ago
Haha, I bet the administrator is regretting not testing the SSH access before trying to harden the router. Rookie mistake!
upvoted 0 times
Narcisa
12 months ago
User 2: Definitely! The administrator should configure SSH on the remote device to log in using SSH.
upvoted 0 times
...
Ashley
12 months ago
User 1: Yeah, that's a big oversight. Testing SSH access is crucial before hardening a router.
upvoted 0 times
...
Willow
1 year ago
User 2: I think the solution is to configure SSH on the remote device to log in using SSH.
upvoted 0 times
...
Sueann
1 year ago
User 1: Yeah, that was definitely a rookie mistake.
upvoted 0 times
...
...
Stephania
1 year ago
D is the way to go. Configuring the enable secret is not the right solution, as that's for local user authentication, not SSH access.
upvoted 0 times
Sharika
1 year ago
Yes, D is the way to go. It ensures SSH is allowed for remote access.
upvoted 0 times
...
Winfred
1 year ago
I agree, D is the correct answer. It allows SSH access to the router.
upvoted 0 times
...
...
Aleisha
1 year ago
I'm not sure. I think it could also be A) Configure SSH on the remote device to log in using SSH.
upvoted 0 times
...
Regenia
1 year ago
I agree with Donette. Enabling SSH with the transport output ssh command should resolve the issue.
upvoted 0 times
...
Donette
1 year ago
I think the correct answer is D) SSH must be allowed with the transport output ssh command.
upvoted 0 times
...
Noemi
1 year ago
I agree with Joanne. The SSH access needs to be explicitly allowed on the router interface for the administrator to be able to log in successfully.
upvoted 0 times
Mose
1 year ago
User3: Yes, that's the way to resolve the issue.
upvoted 0 times
...
Herminia
1 year ago
User2: I agree, the transport output ssh command needs to be allowed for SSH access.
upvoted 0 times
...
Alberto
1 year ago
User1: I think option D is the correct one.
upvoted 0 times
...
...
Joanne
1 year ago
Option D seems like the right choice here. The transport output ssh command is used to enable SSH on the router interface, which is likely the issue the administrator is facing.
upvoted 0 times
Wilford
1 year ago
I would go with option D as well. Enabling SSH with the transport output ssh command is a common solution for SSH access issues.
upvoted 0 times
...
Queenie
1 year ago
I think option A might also work. Configuring SSH on the remote device to log in using SSH could potentially solve the problem.
upvoted 0 times
...
Ivette
1 year ago
I agree, option D is the correct choice. Enabling SSH with the transport output ssh command should resolve the issue.
upvoted 0 times
...
...

Save Cancel