Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 200-301 Exam - Topic 7 Question 64 Discussion

Refer to Exhibit.IP connectivity and OSPF are preconfigured on all devices where necessary. Do not make any changes to the IP addressing or OSPF. The company policy uses connected interfaces and next hops when configuring static routes except for load balancing or redundancy without floating static. Connectivity must be established between subnet 172.20.20.128/25 on the Internet and the LAN at 192.168.0.0/24 connected to SW1:1. Configure reachability to the switch SW1 LAN subnet in router R2.2. Configure default reachability to the Internet subnet in router R1.3. Configure a single static route in router R2 to reach to the Internet subnet considering both redundant links between routers R1 and R2. A default route is NOT allowed in router R2.4. Configure a static route in router R1 toward the switch SW1 LAN subnet where the primary link must be through Ethernet0/1. and the backup link must be through Ethernet0/2 using a floating route. Use the minimal administrative distance value when required.
A) Explanation: Answer as below configuration: On R2: Enable Conf t Ip route 192.168.1.0 255.255.255.0 10.10.31.1 On R1: Enable Conf t Ip route 0.0.0.0 0.0.0.0 10.10.13.3 On R2 Ip route 172.20.20.128 255.255.255.128 e0/2 Ip route 172.20.20.128 255.255.255.128 e0/1 On R1 Ip route 192.168.0.0 255.255.255.0 e0/1 Ip route 192.168.0.0 255.255.255.0 10.10.12.2 3 Save all configurations after every router from anyone of these command Do wr Or Copy run start

Cisco 200-301 Exam - Topic 7 Question 64 Discussion

Actual exam question for Cisco's 200-301 exam
Question #: 64
Topic #: 7
[All 200-301 Questions]

Refer to Exhibit.

IP connectivity and OSPF are preconfigured on all devices where necessary. Do not make any changes to the IP addressing or OSPF. The company policy uses connected interfaces and next hops when configuring static routes except for load balancing or redundancy without floating static. Connectivity must be established between subnet 172.20.20.128/25 on the Internet and the LAN at 192.168.0.0/24 connected to SW1:

1. Configure reachability to the switch SW1 LAN subnet in router R2.

2. Configure default reachability to the Internet subnet in router R1.

3. Configure a single static route in router R2 to reach to the Internet subnet considering both redundant links between routers R1 and R2. A default route is NOT allowed in router R2.

4. Configure a static route in router R1 toward the switch SW1 LAN subnet where the primary link must be through Ethernet0/1. and the backup link must be through Ethernet0/2 using a floating route. Use the minimal administrative distance value when required.

Show Suggested Answer Hide Answer
Suggested Answer: A

by Maryann at Feb 28, 2023, 02:13 PM

Limited Time Offer

25%

Off

Get Premium 200-301 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Roxanne
10 months ago
I thought we were supposed to use floating static routes everywhere?
upvoted 0 times
...
Rodolfo
10 months ago
Just a heads up, the static routes look good!
upvoted 0 times
...
Dona
10 months ago
Wait, why no default route on R2? Seems odd.
upvoted 0 times
...
Ruthann
11 months ago
Totally agree, no changes needed!
upvoted 0 times
...
Nieves
11 months ago
OSPF is already set up, nice!
upvoted 0 times
...
Roosevelt
11 months ago
For R1, I believe we need to prioritize the primary link through Ethernet0/1, but I hope I remember the command structure correctly!
upvoted 0 times
...
Cletus
11 months ago
I feel a bit uncertain about the floating static route on R1. I think it should have a higher administrative distance, but I can't recall the exact value.
upvoted 0 times
...
Helene
11 months ago
I practiced a similar question where we had to configure static routes, and I remember the importance of using the correct next hop for redundancy.
upvoted 0 times
...
Brandon
11 months ago
I think I remember that for R2, we need to set up a static route to the SW1 LAN subnet, but I'm not sure about the exact command syntax.
upvoted 0 times
...
Shantell
11 months ago
Based on the user story, it sounds like the key is handling the pricing and discounts that were originally negotiated with customers. I'm guessing the answer is related to that, so I'll focus on the "contracted pricing" and "entitlements" options.
upvoted 0 times
...
Mable
11 months ago
Hmm, I'm a bit unsure about this. I'll need to review my notes on App Volumes and vCenter Server performance to make sure I understand the key considerations here.
upvoted 0 times
...
Joni
11 months ago
Hmm, I'm a bit unsure about the differences between these mechanisms. I'll need to review my notes on cloud computing characteristics and features.
upvoted 0 times
...
Dorathy
11 months ago
Okay, I've got this. The size of the enterprise is important because it helps you decide whether to use COBIT or SME guidance, which is what option B is getting at. That's the key benefit.
upvoted 0 times
...

Save Cancel