Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 200-301 Exam - Topic 11 Question 58 Discussion

Three switches must be configured for Layer 2 connectivity. The company requires only the designated VLANs to be configured on their respective switches and permitted accross any links between switches for security purposes. Do not modify or delete VTP configurations.The network needs two user-defined VLANs configured:VLAN 110: MARKETINGVLAN 210: FINANCE1. Configure the VLANs on the designated switches and assign them as access ports to the interfaces connected to the PCs.2. Configure the e0/2 interfaces on Sw1 and Sw2 as 802.1q trunks with only the required VLANs permitted.3. Configure the e0/3 interfaces on Sw2 and Sw3 as 802.1q trunks with only the required VLANs permitted.
A) Explanation: Answer as below configuration: Sw1 enbale config t Vlan 210 Name FINANCE Inter e0/1 Switchport access vlan 210 do wr Sw2 Enable config t Vlan 110 Name MARKITING Int e0/1 Switchport acees vlan 110 do wr Sw3 Enable config t Vlan 110 Name MARKITING Vlan 210 Name FINANCE Int e0/0 Switchport access vlan 110 Int e0/1 Switchport access vlan 210 Sw1 Int e0/1 Switchport allowed vlan 210 Sw2 Int e0/2 Switchport trunk allowed vlan 210 Sw3 Int e0/3 Switchport trunk allowed vlan 210 Switchport trunk allowed vlan 210,110

Cisco 200-301 Exam - Topic 11 Question 58 Discussion

Actual exam question for Cisco's 200-301 exam
Question #: 58
Topic #: 11
[All 200-301 Questions]

Three switches must be configured for Layer 2 connectivity. The company requires only the designated VLANs to be configured on their respective switches and permitted accross any links between switches for security purposes. Do not modify or delete VTP configurations.

The network needs two user-defined VLANs configured:

VLAN 110: MARKETING

VLAN 210: FINANCE

1. Configure the VLANs on the designated switches and assign them as access ports to the interfaces connected to the PCs.

2. Configure the e0/2 interfaces on Sw1 and Sw2 as 802.1q trunks with only the required VLANs permitted.

3. Configure the e0/3 interfaces on Sw2 and Sw3 as 802.1q trunks with only the required VLANs permitted.

Show Suggested Answer Hide Answer
Suggested Answer: A

by Alyce at Oct 23, 2022, 02:28 PM

Limited Time Offer

25%

Off

Get Premium 200-301 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Claudio
10 months ago
Sounds good, but what about the trunk configurations?
upvoted 0 times
...
Francine
10 months ago
I think they should have used different VLAN IDs for clarity.
upvoted 0 times
...
Daryl
10 months ago
Wait, did they really spell MARKETING wrong?
upvoted 0 times
...
Claudia
11 months ago
Totally agree, those VLANs make sense for security!
upvoted 0 times
...
Cecil
11 months ago
VLAN 110 is for MARKETING, and VLAN 210 is for FINANCE.
upvoted 0 times
...
Lajuana
11 months ago
I feel a bit uncertain about the access port configurations. Did we use "switchport access vlan" for the correct interfaces? I hope I remember the right interface assignments!
upvoted 0 times
...
Chantell
11 months ago
I recall that we need to ensure only the designated VLANs are allowed on the trunk links. I hope I don't forget to use "switchport trunk allowed vlan" correctly!
upvoted 0 times
...
Marguerita
11 months ago
I practiced a similar question where we had to configure VLANs and trunk ports. I think the trunk command should specify allowed VLANs, but I might mix up the interface numbers.
upvoted 0 times
...
Willodean
11 months ago
I think I remember that we need to create VLANs 110 and 210 on the respective switches, but I'm not sure about the exact commands for the trunk configurations.
upvoted 0 times
...
Jamey
11 months ago
Hmm, I think auto-configuration could apply when a bean is missing, but I'm not sure if it could apply when a bean is present. I'll need to review the details on that.
upvoted 0 times
...
Mona
11 months ago
I'm a little confused on this one. I know Sprint Planning is about planning the work for the next Sprint, but I'm not sure if the options fully capture all the objectives. I'll have to review my notes to be sure.
upvoted 0 times
...
Sang
11 months ago
This question seems straightforward. I think I'll focus on the two key ways mentioned - BPEL processes and mediators.
upvoted 0 times
...
Teri
11 months ago
Okay, let's see. I know we need to set up the dimension names, application name, and server details. Mapping the locations to an entity is also key. I think I've got a good handle on this.
upvoted 0 times
...

Save Cancel