Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

VMware 2V0-41.24 Exam - Topic 1 Question 29 Discussion

An administrator wants to validate the BGP connection status between the Tier-0 Gateway and the upstream physical router.What sequence of commands could be used to check this status on NSX Edge node?
A) - enable <LR-D> - get vrf <ID> - show bgp neighbor
B) - get gateways - vrf <number> - get bgp neighbor
C) - set vrf <ID> - show logical-routers - show <LR-D> bgp
D) - show logical-routers - get vrf - show ip route bgp

VMware 2V0-41.24 Exam - Topic 1 Question 29 Discussion

Actual exam question for VMware's 2V0-41.24 exam
Question #: 29
Topic #: 1
[All 2V0-41.24 Questions]

An administrator wants to validate the BGP connection status between the Tier-0 Gateway and the upstream physical router.

What sequence of commands could be used to check this status on NSX Edge node?

Show Suggested Answer Hide Answer
Suggested Answer: A

To validate the BGP connection status between the Tier-0 Gateway and the upstream physical router on an NSX Edge node, the correct sequence involves enabling the specific logical router (Tier-0 Gateway), checking the VRF (Virtual Routing and Forwarding) context, and then using the show bgp neighbor command to view the BGP session status.

enable <LR-D>: This command enables the logical router interface (Tier-0 Gateway) to access its configuration.

get vrf <ID>: This command checks the specific VRF (used for routing separation) to see the associated routing table.

show bgp neighbor: This command displays the status of the BGP connection, including details about the neighbor relationships and their state.


by Vince at Jun 18, 2026, 10:37 PM

Limited Time Offer

25%

Off

Get Premium 2V0-41.24 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Denise
3 days ago
Option C seems good too, but it feels a bit roundabout.
upvoted 0 times
...
Precious
8 days ago
I prefer option B. It’s straightforward and gets to the point.
upvoted 0 times
...
Coletta
13 days ago
I think option A is the best. It directly checks the BGP neighbor status.
upvoted 0 times
...
Matt
19 days ago
A is definitely the standard approach!
upvoted 0 times
...
Belen
24 days ago
Wait, are we sure D even checks the BGP status?
upvoted 0 times
...
Ngoc
29 days ago
C seems a bit off to me.
upvoted 0 times
...
Rex
1 month ago
I think B is better for clarity.
upvoted 0 times
...
Heidy
1 month ago
Option A is the correct sequence.
upvoted 0 times
...
Xenia
1 month ago
I think option A looks familiar, but I’m not entirely sure if "enable" is necessary before checking the BGP neighbor status.
upvoted 0 times
...
Cathern
2 months ago
I’m a bit confused about the VRF commands. Should we be using "set vrf" or "get vrf"? I can't recall which one is correct.
upvoted 0 times
...
Mitzie
2 months ago
I remember practicing with similar questions, and I feel like "get gateways" might be the right starting point for checking the BGP status.
upvoted 0 times
...
Penney
2 months ago
I think the command to check BGP neighbors is important, but I'm not sure if "show bgp neighbor" is in the right sequence.
upvoted 0 times
...

Save Cancel