Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

SAS A00-260 Exam - Topic 1 Question 59 Discussion

Which statement regarding propagation is FALSE?
B) Propagation can only occur in the direction of the job flow diagram (from beginning to end). Propagation from the end to the beginning is not available.
A) Automatic propagation can be set globally, so every new job will automatically propagate.
C) Automatic propagation that is set globally can be overridden and disabled within a job.
D) Automatic propagation that is set globally or at the job level can be overridden and disabled for a selected transformation.

SAS A00-260 Exam - Topic 1 Question 59 Discussion

Actual exam question for SAS's A00-260 exam
Question #: 59
Topic #: 1
[All A00-260 Questions]

Which statement regarding propagation is FALSE?

Show Suggested Answer Hide Answer
Suggested Answer: B

by Mona at Mar 07, 2024, 07:09 AM

Limited Time Offer

25%

Off

Get Premium A00-260 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Werner
9 months ago
Wait, I thought propagation could go backwards too? That's new to me!
upvoted 0 times
...
Catalina
10 months ago
D sounds right, but can it really be done for any transformation?
upvoted 0 times
...
Grover
10 months ago
C is correct, you can override global settings in a job.
upvoted 0 times
...
Lynelle
10 months ago
I disagree with B, I've seen propagation in both directions.
upvoted 0 times
...
Clare
10 months ago
A is true, automatic propagation can be set globally.
upvoted 0 times
...
Kenneth
11 months ago
I thought that D was true because it mentions overriding at the transformation level, but I need to double-check that against my notes.
upvoted 0 times
...
Jaleesa
11 months ago
I vaguely recall something about overriding global settings, but I can't remember if it applies to transformations too.
upvoted 0 times
...
Glennis
11 months ago
I feel like I've seen a question about propagation direction before, and I think propagation can only go from start to finish, so B might be the false one.
upvoted 0 times
...
Pilar
11 months ago
I think I remember that automatic propagation can be set globally, but I'm not sure if it's true that it applies to every new job.
upvoted 0 times
...
Tequila
11 months ago
Ah, I remember this from the training. Option D is the false statement - automatic propagation can be disabled at the transformation level, not just globally or at the job level.
upvoted 0 times
...
Anjelica
11 months ago
I'm a bit confused on the difference between global and job-level automatic propagation. I'll need to review those concepts.
upvoted 0 times
...
Peggie
11 months ago
Okay, I think I know the answer to this. Propagation can definitely go both ways, not just from beginning to end.
upvoted 0 times
...
Lasandra
11 months ago
Hmm, this is a tricky one. I'll need to carefully read through each option and think about the propagation rules.
upvoted 0 times
...
Rolf
11 months ago
Ah, I know this one! The executive summary is a high-level overview of the organization's disaster recovery efforts, so that's got to be the right answer.
upvoted 0 times
...
Anissa
11 months ago
This question seems pretty straightforward. I think the answer is C - mix points of hot and cold streams, since those would be less prone to thermal fatigue compared to the other options.
upvoted 0 times
...
Albina
11 months ago
Ah, I think I've got it. The key is that the question says the deduplication was enabled properly, but the dedup ratio is still low. So the issue must be with something else, like the copies property or the dedupratio property on the zpool.
upvoted 0 times
...
Emilio
12 months ago
Hmm, I'm a bit unsure about this one. I know we covered risk analysis in class, but I'm having trouble remembering the specific definitions of these different risk types. I'll have to think it through step-by-step.
upvoted 0 times
...
Dorothy
12 months ago
I think it's safe to say the sales won't double, so I'm leaning towards B for a decrease in sales due to higher taxes.
upvoted 0 times
...
Sheldon
2 years ago
I think you're right, so the false statement is C then.
upvoted 0 times
...
Kasandra
2 years ago
But can't automatic propagation be disabled for a selected transformation?
upvoted 0 times
...
Carmelina
2 years ago
I disagree, I believe the false statement is D.
upvoted 0 times
...
Sheldon
2 years ago
I agree with Kasandra, automatic propagation can't be set globally.
upvoted 0 times
...
Kasandra
2 years ago
I think the false statement is A.
upvoted 0 times
...
Joseph
2 years ago
Also, automatic propagation can be disabled for a selected transformation, so option D is true.
upvoted 0 times
...
Reita
2 years ago
Yes, that's correct. So, option A is definitely false.
upvoted 0 times
...
Belen
2 years ago
But can't automatic propagation be overridden and disabled within a job? That statement is true.
upvoted 0 times
...
Venita
2 years ago
I agree, I remember reading that propagation can only happen from beginning to end in the job flow.
upvoted 0 times
...
Reita
2 years ago
I think the statement about automatic propagation being able to occur from end to beginning is FALSE.
upvoted 0 times
...

Save Cancel