Which of the following is not a key feature of GMPLS?
GMPLS is a protocol suite that extends the MPLS signaling and routing capabilities to control different types of switching technologies, such as optical, TDM, and packet switching1. GMPLS has several key features, such as self-discovery, fast protection, and restoration.Self-discovery allows GMPLS nodes to automatically discover their neighbors and exchange information about their capabilities and resources2.Fast protection enables GMPLS nodes to quickly switch to backup paths in case of a failure, without relying on the control plane3.Restoration allows GMPLS nodes to dynamically establish new paths in the network after a failure, using the control plane3. Resource optimization is not a key feature of GMPLS, but rather a potential benefit of using GMPLS to efficiently utilize the network resources and avoid over-provisioning.Reference:
1: Nokia GMPLS-controlled Optical Networks Course | Nokia
2: GMPLS - Nokia
3: Traffic survivability through Protection and Restoration Combined (PRC) - YouTube
[4]: GMPLS: Architecture and Applications - Google Books
Which of the following information is present in every GMPLS-enabled node?
GMPLS-enabled nodes use routing protocols, such as OSPF-TE or ISIS-TE, to exchange information about the topology and the state of the links in the network12.This information includes the link attributes, such as bandwidth, wavelength, protection, and shared risk link groups (SRLGs)3. The state of each link indicates whether it is up or down, available or reserved, and so on. This information is used by GMPLS-enabled nodes to compute feasible paths for LSPs and to avoid routing loops or conflicts. The bandwidth and the frequency of each client path are not present in every GMPLS-enabled node, but only in the ingress and egress nodes that initiate and terminate the LSPs. The list of LSPs created in the entire network is also not present in every GMPLS-enabled node, but only in the nodes that are involved in the LSPs or that maintain a global view of the network.Reference:
1: GMPLS - Nokia
2: Generalized Multi-Protocol Label Switching - Wikipedia
3: Nokia GMPLS-controlled Optical Networks Course | Nokia
What is the purpose of preemption when establishing an LSP?
Preemption is a mechanism that allows a higher priority LSP to tear down an existing lower priority LSP in order to obtain the required resources for its establishment. Preemption can occur when there is not enough bandwidth or other resources available on a link or node to accommodate a new LSP request. In this case, the node can select one or more lower priority LSPs that are using the resources and send them a PathErr message with a Preempt error code. This causes the lower priority LSPs to be terminated and release their resources.The node can then allocate the resources to the higher priority LSP and send a Resv message to confirm its reservation34.Reference:
3: RFC 4829: Label Switched Path (LSP) Preemption Policies for MPLS Traffic Engineering4
4: MPLS Applications User Guide | Juniper Networks5
When should two physical connections belong to the same SRG?
A Shared Risk Link Group (SRLG) is a set of links sharing a common resource, which affects all links in the set if the common resource fails5. These links share the same risk of failure and are therefore considered to belong to the same SRLG. For example, links sharing a common fiber are said to be in the same SRLG because a fault with the fiber might cause all links in the group to fail. SRLGs are used in MPLS and GMPLS networks to provide traffic engineering and protection/restoration mechanisms.When computing the secondary path for an LSP, it is preferable to find a path such that the secondary and primary paths do not have any links in common in case the SRLGs for the primary and secondary paths are disjoint6. This ensures that a single point of failure on a particular link does not bring down both the primary and secondary paths in the LSP.Reference:
5: Shared risk resource group - Wikipedia
6: Shared Risk Link Groups for MPLS | Junos OS | Juniper Networks
Which provisioning steps are common in both CP to plain MP networks?
The provisioning steps that are common in both CP to plain MP networks are node creation, CPB provisioning process, node synchronization, and CPB power balance. These steps are required to create and commission the nodes, provision the cross-connect boards (CPBs), associate the links between the nodes, synchronize the network elements (NEs) with the NFM-T, and balance the power levels of the CPBs.Reference:Nokia GMPLS-controlled Optical Networks Course | Nokia,Nokia Advanced Optical Network Management with NFM-T Course | Nokia
Salman Abbasi
13 days agoDuc Nguyen
27 days agoRajesh Kapoor
1 month agoAmit Sinha
2 months ago