Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Microsoft MB-330 Exam - Topic 6 Question 20 Discussion

You are a functional consultant for a company named Contoso Entertainment System USA (USMF).You need to configure a new quality process for item number M0017. The process must meet the following requirements:Perform an impedance test on 100 percent of the units purchased.Initiate the test after the product receipt is posted.To complete this task, sign in to Dynamics 365 portal.
A) Explanation: Configure Item Sampling to specify 100 percent of the units. Configure Quality Association to specify what test to run and configure the test to run after the receipt is posted. Configure Item Sampling. Go toInventory management > Setup > Quality control > Item sampling. ClickNew. In theItem samplingfield, type the name 100%. In theDescriptionfield, type a value (100%). In the Quantity specification field, select percent. In theValuefield, enter a number (100) ClickSave. Close the page. Configure a Quality Association Go toInventory management > Setup > Quality control > Quality associations. ClickNew. In theReference typefield, select Purchase. In theItem codefield, select Table. In theItemfield, select the item M0017. In theEvent typefield, select Product Receipt. In theExecutionfield, select After. Expand or collapse theSpecificationssection. In theTest groupfield, find and select the Impedance test. ClickSave. Close the page.

Microsoft MB-330 Exam - Topic 6 Question 20 Discussion

Actual exam question for Microsoft's MB-330 exam
Question #: 20
Topic #: 6
[All MB-330 Questions]

You are a functional consultant for a company named Contoso Entertainment System USA (USMF).

You need to configure a new quality process for item number M0017. The process must meet the following requirements:

Perform an impedance test on 100 percent of the units purchased.

Initiate the test after the product receipt is posted.

To complete this task, sign in to Dynamics 365 portal.

Show Suggested Answer Hide Answer
Suggested Answer: A

https://docs.microsoft.com/en-us/dynamics365/supply-chain/inventory/tasks/set-up-quality-orders

https://docs.microsoft.com/en-us/dynamics365/supply-chain/inventory/enable-quality-management

by Maurine at May 05, 2022, 08:15 PM

Limited Time Offer

25%

Off

Get Premium MB-330 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Bernardo
10 months ago
I’m surprised they want every single unit tested. Is that really necessary?
upvoted 0 times
...
Yvonne
10 months ago
Yup, just follow those steps in Dynamics 365!
upvoted 0 times
...
Minna
11 months ago
Wait, does it really need to be 100%? Seems excessive.
upvoted 0 times
...
Shonda
11 months ago
Totally agree, easy peasy!
upvoted 0 times
...
Kirk
11 months ago
Sounds straightforward, just set it to 100%.
upvoted 0 times
...
Pansy
11 months ago
I think the steps for configuring the quality association are straightforward, but I’m a bit confused about the execution timing—does it really need to be set to "After"?
upvoted 0 times
...
Wilda
11 months ago
I believe the impedance test should be linked to the product receipt event, but I might be mixing it up with another test type we covered.
upvoted 0 times
...
Earlean
11 months ago
I think we need to set the item sampling to 100 percent, but I'm not entirely sure how to navigate to that section in Dynamics 365.
upvoted 0 times
...
Paz
11 months ago
I remember practicing a similar question about quality associations, but I can't recall if we need to specify the test group before saving.
upvoted 0 times
...
Ronny
11 months ago
This is a tricky one, but I'm going to take it step-by-step. First, I'll analyze the statements in Session 1 and Session 2 separately, then I'll consider how they might interact with each other.
upvoted 0 times
...
Amira
11 months ago
I'm a bit confused by the question. The images all look the same, so I'm not sure how to differentiate between the options. I'll need to think this through carefully.
upvoted 0 times
...
Verona
11 months ago
Wait, I'm a little confused. Why would we use an Instance Template to give the Service Account access? Isn't that more for managing the instances themselves, rather than just listing them? I'll need to re-read the question carefully.
upvoted 0 times
...

Save Cancel