Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Microsoft AZ-700 Exam - Topic 5 Question 13 Discussion

You have an Azure virtual network named Vnet1 and an on-premises network.The on-premises network has policy-based VPN devices. In Vnet1, you deploy a virtual network gateway named GW1 that uses a SKU of VpnGw1 and is route-based.You have a Site-to-Site VPN connection for GW1 as shown in the following exhibit.You need to ensure that the on-premises network can connect to the route-based GW1. What should you do before you create the connection?
A) Set Use Azure Private IP Address to Enabled
B) Set IPsec / IKE policy to Custom.
C) Set Connection Mode to ResponderOnly
D) Set BGP to Enabled

Microsoft AZ-700 Exam - Topic 5 Question 13 Discussion

Actual exam question for Microsoft's AZ-700 exam
Question #: 13
Topic #: 5
[All AZ-700 Questions]

You have an Azure virtual network named Vnet1 and an on-premises network.

The on-premises network has policy-based VPN devices. In Vnet1, you deploy a virtual network gateway named GW1 that uses a SKU of VpnGw1 and is route-based.

You have a Site-to-Site VPN connection for GW1 as shown in the following exhibit.

You need to ensure that the on-premises network can connect to the route-based GW1. What should you do before you create the connection?

Show Suggested Answer Hide Answer
Suggested Answer: A

by Bernardo at May 08, 2022, 07:30 PM

Limited Time Offer

25%

Off

Get Premium AZ-700 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Scarlet
10 months ago
Setting Connection Mode to ResponderOnly doesn't seem right for this setup.
upvoted 0 times
...
Renea
10 months ago
Wait, are you sure BGP is the only option?
upvoted 0 times
...
Arlen
11 months ago
I thought you could use custom IPsec/IKE policies instead?
upvoted 0 times
...
Maryann
11 months ago
Totally agree, BGP is essential here!
upvoted 0 times
...
Herman
11 months ago
You need to set BGP to Enabled for route-based gateways.
upvoted 0 times
...
Deonna
11 months ago
I believe enabling the Azure Private IP Address is important for connectivity, but I’m not confident if it’s the first step before creating the connection.
upvoted 0 times
...
Chauncey
11 months ago
I’m a bit confused about the connection mode options. I thought ResponderOnly was for specific scenarios, but I can't recall if it’s necessary for this setup.
upvoted 0 times
...
Elly
11 months ago
This question feels familiar; I practiced a similar one where we had to enable BGP for a route-based VPN. I wonder if that applies here too.
upvoted 0 times
...
Elenor
11 months ago
I think I remember something about needing to set the IPsec/IKE policy to Custom for policy-based VPNs, but I'm not entirely sure if that's the only step needed.
upvoted 0 times
...
Janessa
11 months ago
Alright, this is a good one. I remember learning about the queue management improvements in the IOM3, but I'm drawing a blank on the details. I'll need to carefully read through the answer choices and see if I can eliminate any of them.
upvoted 0 times
...
Lavonda
11 months ago
Logging seems off for this context. I think it's definitely between MPLS LSP ping or RSVP. I wish I had focused more on those specific topics!
upvoted 0 times
...
Miesha
11 months ago
Hmm, I'm a bit unsure about this one. I know we covered WebLogic clustering in class, but the details around distributed JMS destinations are a bit fuzzy for me. I'll have to re-read the question closely and try to recall the best practices.
upvoted 0 times
...
otwb2pX
3 years ago
B. The configuration option is part of the custom IPsec/IKE connection policy. If you enable the policy-based traffic selector option, you must specify the complete policy (IPsec/IKE encryption and integrity algorithms, key strengths, and SA lifetimes) From
upvoted 1 times
...

Save Cancel