Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Huawei Exam H13-629 Topic 1 Question 50 Discussion

Actual exam question for Huawei's H13-629 exam
Question #: 50
Topic #: 1
[All H13-629 Questions]

In a A VTL6900-I system, the backup server connected to it is the Linux operating system. The backup server and the VTL6900-I system are directly connected through the FC.

The server identifies the device information as shown below. After the backup server is configured as a backup client for the VTL6900-I system and the backup VTL system on the server virtual library process, which the following operation and description is correct:

(Multiple choice.)

Show Suggested Answer Hide Answer
Suggested Answer: D

by Tijuana at Jul 03, 2024, 07:20 PM

Limited Time Offer

25%

Off

Get Premium H13-629 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel
Willodean
3 months ago
I heard the VTL6900-I system runs on a special Linux distro called 'Tape-a-Tux'.
upvoted 0 times
...
Karon
3 months ago
Option D is also correct. The device labeled 2 is the information for the scanned tape.
upvoted 0 times
Joseph
1 months ago
D) As shown in the figure, of the devices identified on the server side, the device labeled 2 is the information for the scanned tape.
upvoted 0 times
...
Valentine
1 months ago
C) As shown in the figure, among the devices identified on the server side, the device labeled 1 is the scanned library.
upvoted 0 times
...
Johnson
2 months ago
B) Server-side identification has been detected with the library device command is cat / proc / scsi / scsi.
upvoted 0 times
...
Berry
2 months ago
A) When configuring the backup client on the VTL side, you need to know that the WWPN of the FC port that connects the VTL to the VTL is available on the server in the sys /class / fc_host directory and subdirectory to the corresponding WWPN port.
upvoted 0 times
...
...
Ressie
3 months ago
Option C looks good. The device labeled 1 is likely the scanned library, as you mentioned.
upvoted 0 times
...
Ilene
3 months ago
I'm not sure about option B. The server-side identification may not necessarily be done using the cat /proc/scsi/scsi command.
upvoted 0 times
Misty
1 months ago
C) As shown in the figure, among the devices identified on the server side, the device labeled 1 is the scanned library.
upvoted 0 times
...
Joni
2 months ago
B) I think you're right. Server-side identification may not be done using the cat /proc/scsi/scsi command.
upvoted 0 times
...
Tyisha
2 months ago
A) When configuring the backup client on the VTL side, you need to know that the WWPN of the FC port that connects the VTL to the VTL is available on the server in the sys /class / fc_host directory and subdirectory to the corresponding WWPN port.
upvoted 0 times
...
...
Shawnna
3 months ago
Option A seems to be the correct answer. The WWPN of the FC port on the VTL is needed to configure the backup client on the VTL side.
upvoted 0 times
Emmett
2 months ago
Make sure to check that directory for the corresponding WWPN port when setting up the backup client.
upvoted 0 times
...
Samira
2 months ago
Yes, that's right. The WWPN is available on the server in the sys/class/fc_host directory.
upvoted 0 times
...
Carmelina
2 months ago
I think option A is correct. You need the WWPN of the FC port on the VTL to configure the backup client.
upvoted 0 times
...
...
Abel
4 months ago
I'm not sure about that. I think the correct answer might be C because the scanned library device is labeled 1 on the server side.
upvoted 0 times
...
Mee
4 months ago
I agree with Dorothy. Knowing the WWPN is crucial for configuring the backup client on the VTL side.
upvoted 0 times
...
Dorothy
4 months ago
I think the correct answer is A because we need to know the WWPN of the FC port connecting the VTL to the server.
upvoted 0 times
...

Save Cancel