Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Huawei H13-624 Exam - Topic 1 Question 97 Discussion

In the Huawei dual-active disaster recovery solution, the peak write bandwidth of an application needs to be 10MB/s for single selection, and the average write bandwidth needs to be 200KB/s, and the average write bandwidth is 200KB/s.The I/O volume is 4KB. The bandwidth utilization rate is 70%. How much bandwidth does the application need to deploy synchronous remote replication?
D) 114.3Mbit/s
A) 0MB/s
B) 200KB/s
C) 2.23MB/s

Huawei H13-624 Exam - Topic 1 Question 97 Discussion

Actual exam question for Huawei's H13-624 exam
Question #: 97
Topic #: 1
[All H13-624 Questions]

In the Huawei dual-active disaster recovery solution, the peak write bandwidth of an application needs to be 10MB/s for single selection, and the average write bandwidth needs to be 200KB/s, and the average write bandwidth is 200KB/s.

The I/O volume is 4KB. The bandwidth utilization rate is 70%. How much bandwidth does the application need to deploy synchronous remote replication?

Show Suggested Answer Hide Answer
Suggested Answer: D

by Elouise at May 03, 2026, 05:52 AM

Limited Time Offer

25%

Off

Get Premium H13-624 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Theron
2 days ago
Yeah, but the average write bandwidth is 200KB/s. It could be a factor.
upvoted 0 times
...
Cherilyn
7 days ago
I feel like B) 200KB/s is too low for synchronous replication.
upvoted 0 times
...
Ozell
12 days ago
I agree, C seems right. The calculations add up.
upvoted 0 times
...
Mattie
17 days ago
This question is tricky! I'm leaning towards C) 2.23MB/s.
upvoted 0 times
...
Dyan
23 days ago
I still think D) is worth considering. It covers more ground.
upvoted 0 times
...
Micaela
28 days ago
So, C) might be the best choice after all.
upvoted 0 times
...
Tess
1 month ago
True! We need to factor in the 70% utilization.
upvoted 0 times
...
Edda
1 month ago
But remember, the utilization rate affects the final bandwidth needed!
upvoted 0 times
...
Dyan
1 month ago
I'm leaning towards D) 114.3Mbit/s. It sounds more realistic for remote replication.
upvoted 0 times
...
Lawana
2 months ago
I agree with Tess. The average bandwidth seems low for sync.
upvoted 0 times
...
Tess
2 months ago
I think the answer is C) 2.23MB/s. It fits the peak write bandwidth.
upvoted 0 times
...
Micaela
2 months ago
This question is tricky! I feel unsure about the calculations.
upvoted 0 times
...
Buck
2 months ago
Definitely not 0MB/s, that’s for sure!
upvoted 0 times
...
Wenona
2 months ago
Wait, is it really 2.23MB/s? That seems low!
upvoted 0 times
...
Augustine
2 months ago
I agree, but how does that relate to the options given?
upvoted 0 times
...
Xochitl
3 months ago
I think the average write bandwidth is 200KB/s.
upvoted 0 times
...
Vallie
3 months ago
The peak write bandwidth is 10MB/s, right?
upvoted 0 times
...
Sueann
3 months ago
I feel like I’ve seen a question like this before, and I think we might need to convert the final answer into Mbit/s. That could be important for choosing the right option.
upvoted 0 times
...
Emiko
5 months ago
I’m a bit confused about whether to use the peak or average write bandwidth for the calculation. Should we be focusing on the peak since it’s higher?
upvoted 0 times
...
Tiera
5 months ago
I remember a similar question about bandwidth utilization rates. If I recall correctly, we need to adjust the bandwidth based on the 70% utilization.
upvoted 0 times
...
Felicidad
5 months ago
I think the key here is to calculate the required bandwidth based on the peak and average write bandwidths. But I'm not entirely sure how to factor in the I/O volume.
upvoted 0 times
...

Save Cancel