Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Huawei H13-511_V5.5 Exam - Topic 3 Question 2 Discussion

Actual exam question for Huawei's H13-511_V5.5 exam
Question #: 2
Topic #: 3
[All H13-511_V5.5 Questions]

SIMULATION

Complete the following configuration file for a network interface card (NIC) in the openEuler operating system to set a static IP address and enable the NIC to automatically start upon system boot.

TYPE=Ethernet

BOOTPROTO=_____

NAME=enp0s4

DEVICE=enp0s4

ONBOOT=_____

IPADDR=172.28.100.100

NETMASK=255.255.255.0

Show Suggested Answer Hide Answer
Suggested Answer: A

Correct Answe r is: BOOTPROTO=static, ONBOOT=yes

In HCIA--Cloud Computing (Operating System Basics), Linux network interface configuration is a foundational skill, and openEuler follows the standard Red Hat--style network configuration syntax.

To configure a static IP address, the parameter BOOTPROTO must be set to static. This tells the operating system not to request an IP address from a DHCP server and instead use the manually configured values such as IPADDR and NETMASK.

To ensure that the NIC is automatically activated when the system boots, the parameter ONBOOT must be set to yes. If ONBOOT is set to no, the interface will remain down after boot and must be manually started.

Therefore, the completed and correct configuration is:

BOOTPROTO=static

ONBOOT=yes

BOOTPROTO=static Uses a fixed IP address

ONBOOT=yes Enables automatic startup at system boot


by Ezekiel at Jan 29, 2026, 01:18 AM

Limited Time Offer

25%

Off

Get Premium H13-511_V5.5 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Princess
1 day ago
Hmm, wonder if I can set this up with DHCP instead. Gotta keep my options open.
upvoted 0 times
...
Matthew
6 days ago
Looks good, but I hope I don't have to reboot to see the changes take effect.
upvoted 0 times
...
Melvin
11 days ago
BOOTPROTO=static and ONBOOT=yes, easy peasy!
upvoted 0 times
...
Ashlyn
17 days ago
Static IP address, nice! I'm ready to get this NIC up and running.
upvoted 0 times
...
Cora
22 days ago
I keep mixing up the options for BOOTPROTO; could it also be "none"? I need to double-check that.
upvoted 0 times
...
Coleen
27 days ago
This reminds me of a similar question we practiced where we had to configure a DHCP setup. I think the syntax is pretty similar.
upvoted 0 times
...
Melinda
2 months ago
I'm not entirely sure about ONBOOT, but I feel like it needs to be "yes" to enable the NIC at boot.
upvoted 0 times
...
Zachary
2 months ago
I think for BOOTPROTO, it should be set to "static" since we're using a static IP.
upvoted 0 times
...
Toshia
2 months ago
Ugh, I'm a little unsure about this one. Configuring network interfaces can be a bit finicky. I better double-check my work before submitting.
upvoted 0 times
...
Isadora
2 months ago
No problem, I've done this kind of thing before. Just need to fill in the blanks with the right values. Shouldn't be too tricky.
upvoted 0 times
...
Pearly
2 months ago
Whoa, I'm not too familiar with openEuler. Gotta make sure I get the syntax right for this config file. Better review the documentation carefully.
upvoted 0 times
...
Jerry
3 months ago
Okay, let me think this through. I need to set the BOOTPROTO to static and the ONBOOT to yes. Should be a pretty simple configuration.
upvoted 0 times
...
Lynelle
3 months ago
Hmm, this looks straightforward. I think I can handle setting the static IP and enabling the NIC on boot.
upvoted 0 times
...

Save Cancel