Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25

- Free Preparation Discussions

HPE7-A07 Exam - Topic 1 Question 34 Discussion

Actual exam question for HP's HPE7-A07 exam

Question #: 34
Topic #: 1

[All HPE7-A07 Questions]

Refer to the CLI output below:

What statement about the output above is correct?

AThe port-access role was configured with gateway-role visitor

BThe secondary tunnel endpoint IP is 10.10-10.151.

CThe client authenticated using dot1x.

DThe UBT zone was configured to use a user-defined VRF

Show Suggested Answer

Suggested Answer: B

The CLI output indicates a tunnel creation process, where 'SW hw tun created' refers to the switch hardware tunnel being created. The line mentioning 'BYP-10.10.10.101 -> SW hw tun created to 10.10.10.151 tunnel 15.' implies that a tunnel was established to the secondary tunnel endpoint with the IP address 10.10.10.151. This is a common configuration for User-Based Tunneling (UBT) setups where traffic is tunneled to a specific endpoint.

by Emiko at May 02, 2025, 08:49 AM

Limited Time Offer

25%

Off

Get Premium HPE7-A07 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Roslyn

8 months ago

Not sure about that, seems off to me.

upvoted 0 times

...

Ellsworth

9 months ago

Totally agree, the gateway-role visitor is set up!

upvoted 0 times

...

Kayleigh

9 months ago

The client authenticated using dot1x.

upvoted 0 times

...

Alaine

9 months ago

Wait, is the secondary tunnel endpoint really 10.10-10.151?

upvoted 0 times

...

Shayne

9 months ago

I think the UBT zone is using a user-defined VRF.

upvoted 0 times

...

Rashida

10 months ago

I vaguely remember discussing UBT zones and VRFs, but I can't remember if it was user-defined or not.

upvoted 0 times

...

Denny

10 months ago

I’m leaning towards option C about dot1x authentication, but I need to double-check what the output actually shows.

upvoted 0 times

...

Lucille

10 months ago

This question feels familiar; I think we had a practice question about tunnel endpoints, but I can't recall the exact IP format.

upvoted 0 times

...

German

10 months ago

I remember something about the port-access role, but I'm not sure if it specifically mentioned "gateway-role visitor."

upvoted 0 times

...

Lakeesha

10 months ago

I'm a bit unsure about some of the networking terminology in this output. I'll need to review my notes to make sure I understand the concepts before attempting to answer.

upvoted 0 times

...

Eleonore

11 months ago

This is a good example of the type of question I've been practicing. I feel confident I can analyze the output and choose the correct statement.

upvoted 0 times

...

Lillian

11 months ago

Okay, the key details I see are the port-access role, the tunnel endpoint IP, the authentication method, and the UBT zone configuration. I think I can use those to figure out the right answer.

upvoted 0 times

...

Ozell

11 months ago

Hmm, the output has a lot of information. I'll need to read through it closely and make sure I understand what each part is referring to before I can select the right answer.

upvoted 0 times

...

Horace

11 months ago

This looks like a pretty straightforward CLI output question. I'll carefully review the details and options to determine the correct statement.

upvoted 0 times

...

Aleta

1 year ago

That's a good point, Odette. It could be either C or D.

upvoted 0 times

...

Odette

1 year ago

I believe it could also be D) The UBT zone was configured to use a user-defined VRF.

upvoted 0 times

...

Tomas

1 year ago

Wow, these exam questions are really out there. I'm just hoping I don't accidentally select the 'Become a Jedi Knight' option by mistake.

upvoted 0 times

...

Youlanda

1 year ago

I agree with Aleta, the output shows dot1x authentication.

upvoted 0 times

...

Gene

1 year ago

D? Nah, the UBT zone was definitely not configured to use a user-defined VRF. These options are getting sillier by the minute.

upvoted 0 times

Danilo

1 year ago

C) The client authenticated using dot1x.

upvoted 0 times

...

Amber

1 year ago

B) The secondary tunnel endpoint IP is 10.10-10.151.

upvoted 0 times

...

Geraldine

1 year ago

A) The port-access role was configured with gateway-role visitor

upvoted 0 times

...

...

Isaac

1 year ago

The client authenticated using dot1x, so C is the correct answer. Easy one!

upvoted 0 times

...

Aleta

1 year ago

I think the correct statement is C) The client authenticated using dot1x.

upvoted 0 times

...

Anglea

1 year ago

The port-access role was configured with gateway-role visitor, so A seems to be the right answer here.

upvoted 0 times

Krissy

1 year ago

User 2: Yeah, that's correct. A) The port-access role was configured with gateway-role visitor.

upvoted 0 times

...

Yong

1 year ago

User 1: I think the port-access role was configured with gateway-role visitor.

upvoted 0 times

...

...

Alpha

1 year ago

Hmm, the secondary tunnel endpoint IP seems to be 10.10.10.151, not 10.10-10.151. Looks like option B is incorrect.

upvoted 0 times

Martina

1 year ago

User 3: So, the correct statement must be related to something else in the output.

upvoted 0 times

...

Polly

1 year ago

User 2: Yeah, that's correct. Option B is incorrect.

upvoted 0 times

...

Arlette

1 year ago

User 1: I think the secondary tunnel endpoint IP is 10.10.10.151, not 10.10-10.151.

upvoted 0 times

...

...