Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

HPE6-A85 Exam - Topic 1 Question 54 Discussion

Which commands are used to set a default route to 10.4.5.1 on an Aruba CX switch when ln-band management using an SVl is being used?
C) ip route 0.0 0 0/0 10.4.5.1
A) iP default-gateway 10.4.5.1
B) ip route 0 0 0.070 10.4 5.1 vrf mgmt
D) default-gateway 10.4.5.1

HPE6-A85 Exam - Topic 1 Question 54 Discussion

Actual exam question for HP's HPE6-A85 exam
Question #: 54
Topic #: 1
[All HPE6-A85 Questions]

Which commands are used to set a default route to 10.4.5.1 on an Aruba CX switch when ln-band management using an SVl is being used?

Show Suggested Answer Hide Answer
Suggested Answer: C

The command that is used to set a default route to 10.4.5.1 on an Aruba CX switch when in-band management using an SVI is being used is ip route 0.0 0 0/0 10.4.5.1 . This command specifies the destination network address (0.0 0 0) and prefix length (/0) and the next-hop address (10.4.5.1) for reaching any network that is not directly connected to the switch. The default route applies to the default VRF Virtual Routing and Forwarding. VRF is a technology that allows multiple instances of a routing table to co-exist within the same router at the same time. VRFs are typically used to segment network traffic for security, privacy, or administrative purposes. , which is used for in-band management traffic that goes through an SVI Switch Virtual Interface. SVI is a virtual interface on a switch that allows the switch to route packets between different VLANs on the same switch or different switches that are connected by a trunk link.An SVI is associated with a VLAN and has an IP address and subnet mask assigned to it12. Reference:1https://www.arubanetworks.com/techdocs/AOS-CX/10_08/HTML/ip_route_4100i-6000-6100-6200/Content/Chp_StatRoute/def-rou.htm2https://www.arubanetworks.com/techdocs/AOS-CX/10_08/HTML/ip_route_4100i-6000-6100-6200/Content/Chp_VRF/vrf-overview.htm


by Lamonica at Apr 04, 2026, 10:44 PM

Limited Time Offer

25%

Off

Get Premium HPE6-A85 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Irving
2 months ago
C seems correct too, but the syntax looks off to me.
upvoted 0 times
...
Erin
2 months ago
I’m leaning towards B. It specifies the VRF, which is crucial.
upvoted 0 times
...
Reita
2 months ago
I think option A is the simplest. Just set the default gateway.
upvoted 0 times
...
Lakeesha
2 months ago
I’m not sure about B, seems off to me.
upvoted 0 times
...
Dominga
2 months ago
Wait, is it really that complicated?
upvoted 0 times
...
Kiley
2 months ago
Definitely B, that’s how you set it for VRF management.
upvoted 0 times
...
Leonor
4 months ago
I thought it was A) ip default-gateway 10.4.5.1?
upvoted 0 times
...
Solange
4 months ago
The correct command is B) ip route 0 0 0.0 10.4.5.1 vrf mgmt.
upvoted 0 times
...
Buddy
5 months ago
I’m leaning towards option B, but I’m confused about the VRF part. We didn’t cover that in detail.
upvoted 0 times
...
Eugene
5 months ago
I feel like "ip default-gateway" is more for layer 2 switches, but I can't recall if it applies here.
upvoted 0 times
...
Valentine
5 months ago
I remember there was a question about default routes in our last practice exam, and I think "ip route 0.0.0.0 0.0.0.0 10.4.5.1" was the right format.
upvoted 0 times
...
Amie
5 months ago
I think the command for setting a default route is similar to what we practiced, but I'm not sure if it's "ip route" or "default-gateway."
upvoted 0 times
...

Save Cancel