HPE6-A85 Exam - Topic 1 Question 2 Discussion

Actual exam question for HP's HPE6-A85 exam

Question #: 2
Topic #: 1

You have been asked to onboard a new Aruba 6300M in a customer deployment You are working remotely rather than on-site You have a colleague installing the switch The colleague has provided you with a remote console session to configure the edge switch You have been asked to configure a link aggregation going back to the cores using interfaces 1/1/51 and 1/1/52 The Senior Engineer of the project has asked you to configure the switch and 1Q uplink with these guidelines

1. Add VLAN 20 to the local VLAN database with name Mgmt

2. Add L3 SVl on VLAN 20 for Management using address 10 in the 10.1.1 0/24 subnet 3. Add LAG 1 using LACP mode active for the uplink

4 use vlan 20 as the native vlan on the LAG 5. Make sure the interfaces are all ON.

Which configuration script will achieve the task?

AEdge1# conf t vlan 20 name Mgmt interface vlan 20 ip address 10.1.1.10/24 no shut interface lag 1 shut vlan access 20 lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut

BEdgel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1.1 10/24 no shut interface 1/1/51.1/1/52 shut vlan trunk native 20 vlan trunk allowed all lag 1 lacp
mode active interface 1/1/51.1/1/52 no shut

CEdgel# conf t vlan 20 name Mgmt interface vlan 20 ip address 10 1 1 10/24 no shut interface lag 1 shut vlan trunk native 20 vlan trunk allowed all lacp mode active Int 1/1/51.1/1/52 shut no routing lag 1 interface lag 1 no shut interface 1/1/51.1/1/52 no shut

Dconf t vlan 20 name Mgmt ip address 10 1 1.10/24 no shut interface lag 1 shut vlan trunk native 1 vlan trunk allowed all lacp mode active int 1/1/51.1/1/52 shut no routing interface lag 1 no shut interface 1/1/51.1/1/52 no shut

Show Suggested Answer

Suggested Answer: C

This configuration script will achieve the task as it follows the guidelines given by the Senior Engineer. It creates VLAN 20 with name Mgmt, adds L3 SVI on VLAN 20 with IP address 10.1.1.10/24, creates LAG 1 with LACP mode active for the uplink, uses VLAN 20 as the native VLAN on the LAG, and ensures that the interfaces are all ON. Reference: https://www.arubanetworks.com/techdocs/AOS-CX/10.04/HTML/5200-6790/GUID-8F0E7E8B-0F4B-4A3C-AE7F-0F1B5A7F9C5D.html

by Willodean at Oct 05, 2023, 06:45 PM

Limited Time Offer

25%

Off

Get Premium HPE6-A85 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Nettie

3 months ago

Wait, is the IP address in option D even valid?

upvoted 0 times

...

Latrice

3 months ago

D? Really? That one doesn’t even have the right native VLAN!

upvoted 0 times

...

Ronnie

4 months ago

C seems a bit off with the interface commands.

upvoted 0 times

...

Carin

4 months ago

I think B has some syntax issues, not sure it’ll work.

upvoted 0 times

...

Jody

4 months ago

Looks like option A is the most complete.

upvoted 0 times

...

Shelia

4 months ago

I definitely remember that we need to use LACP in active mode, but I’m confused about the IP address configuration in the options.

upvoted 0 times

...

Miles

4 months ago

I recall that the native VLAN should be set correctly on the LAG, but I can't remember if it should be "vlan access" or "vlan trunk."

upvoted 0 times

...

Timmy

4 months ago

I think option A looks familiar, but I feel like there might be a mistake with the interface commands.

upvoted 0 times

...

Ressie

5 months ago

I remember we practiced adding VLANs and configuring LAGs, but I'm not sure about the exact syntax for the interface commands.

upvoted 0 times

...

Anna

5 months ago

Hmm, I'm a bit unsure about the IP address for the SVI. The question says to use the 10.1.1.0/24 subnet, but it doesn't specify the exact IP address. I'll need to make sure I get that right.

upvoted 0 times

...

Irene

5 months ago

I think I've got it. The key is to make sure the LAG is using VLAN 20 as the native VLAN and that all the interfaces are in the "on" state. I'll double-check my work, but I'm feeling pretty confident about this one.

upvoted 0 times

...

Cassandra

5 months ago

Okay, let me take a closer look at the guidelines. We need to create VLAN 20 with the name "Mgmt", add an SVI on that VLAN, and configure a link aggregation group (LAG) using LACP mode active on interfaces 1/1/51 and 1/1/52.

upvoted 0 times

...

Adolph

5 months ago

This question looks straightforward, but I want to make sure I understand the requirements correctly before I start configuring the switch.

upvoted 0 times

...

Marti

5 months ago

Partitioning the data is definitely the way to go. That will make the queries much more efficient by limiting the amount of data that needs to be scanned. I'd also consider converting to Parquet format to take advantage of the performance benefits.

upvoted 0 times

...

Bernadine

5 months ago

This looks like a straightforward question about creating a new tenant using the Cobra SDK. I think I've seen this type of syntax before, so I'll give it a shot.

upvoted 0 times

...

Shayne

5 months ago

This question seems straightforward, I'm pretty confident I know the answer.

upvoted 0 times

...

Karon

5 months ago

Okay, let's see. I think incoming mail policies and blocklists would be the two features used to control email delivery based on the sender. The incoming mail policies allow you to set rules for how to handle emails from certain senders, and the blocklists let you block specific senders.

upvoted 0 times

...

Herminia

5 months ago

Committing to customer shipment dates is important, but does it directly affect the master production schedule? I feel a bit uncertain about that.

upvoted 0 times

...