Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

HP Exam HPE6-A73 Topic 1 Question 106 Discussion

Actual exam question for HP's HPE6-A73 exam
Question #: 106
Topic #: 1
[All HPE6-A73 Questions]

A network administrator is tasked to set up BGP in the company's network. The administrator is defining an eBGP peering between an AOS-CX switch and a directly-connected service provider. The administrator has configured the following on the AOS-CX switch:

However, when using the "show bgp all summary" command, the state does not display "Established" for the eBGP peer. What must the administrator configure to fix this issue?

Show Suggested Answer Hide Answer
Suggested Answer: C

by Lili at Dec 07, 2024, 01:59 AM

Limited Time Offer

25%

Off

Get Premium HPE6-A73 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel
Audrie
7 months ago
Well, this one's a no-brainer. D is the solution, and the administrator should've known that from the start. Just connect that BGP session to the loopback, and Bob's your uncle!
upvoted 0 times
...
Raina
7 months ago
The answer is D, no doubt about it. I bet the administrator is scratching their head right now, wondering why the session won't come up.
upvoted 0 times
Nan
6 months ago
Definitely. The administrator just needs to make that change and check the status again.
upvoted 0 times
...
Harris
6 months ago
That makes sense. The session should come up after that.
upvoted 0 times
...
Jonell
6 months ago
Yes, I agree. Configuring the update-source to loopback0 should fix the issue.
upvoted 0 times
...
Casey
6 months ago
I think the administrator should configure option D.
upvoted 0 times
...
...
Tish
7 months ago
I have encountered similar problems before, and using the update-source command with the loopback interface has helped me establish BGP peering. So, I think option D could be the correct answer.
upvoted 0 times
...
Roselle
7 months ago
Option D is the clear winner here. Connecting the BGP session to the loopback interface is the standard practice for network stability.
upvoted 0 times
...
Malcolm
7 months ago
I'm not sure about that. I think option D) router bgp 64500 neighbor 192.168.1.1 update-source loopback0 could also be a solution to the issue.
upvoted 0 times
...
Gerry
7 months ago
Haha, looks like the administrator forgot to connect the dots on this one. D is the way to go, trust me.
upvoted 0 times
Pamella
6 months ago
Thanks for the tip, I'll go with option D to configure the update-source.
upvoted 0 times
...
Eden
6 months ago
Yeah, D is the way to go to establish the eBGP peering.
upvoted 0 times
...
Carlota
6 months ago
I think D is the correct option to fix the issue.
upvoted 0 times
...
...
Iesha
7 months ago
I agree with you, Luis. The eBGP peering may require the ebgp-multihop command to establish the connection.
upvoted 0 times
...
Carma
8 months ago
I'm pretty sure the answer is D. The administrator needs to configure the update-source to be the loopback interface to establish the BGP session.
upvoted 0 times
Shannon
7 months ago
I'm pretty sure the answer is D. The administrator needs to configure the update-source to be the loopback interface to establish the BGP session.
upvoted 0 times
...
Portia
7 months ago
D) router bgp 64500 neighbor 192.168.1.1 update-source loopback0
upvoted 0 times
...
Carla
7 months ago
C) router bgp 64500 address-family ipv4 unicast neighbor 192.168.1.1 activate
upvoted 0 times
...
Chuck
7 months ago
B) router bgp 64500 enable
upvoted 0 times
...
Marcelle
7 months ago
A) router bgp 64500 neighbor 192.168.1.1 ebgp-multihop
upvoted 0 times
...
...
Luis
8 months ago
I think the correct answer is A) router bgp 64500 neighbor 192.168.1.1 ebgp-multihop
upvoted 0 times
...

Save Cancel