Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

HP Exam HPE6-A72 Topic 4 Question 53 Discussion

Actual exam question for HP's HPE6-A72 exam
Question #: 53
Topic #: 4
[All HPE6-A72 Questions]

Interface 1/1/1 is up

Admin state is up

Link transitions: 1

Description: TO_PC-1

Hardware: Ethernet, MAC Address: 00:11:22:33:44:55

MTU 1500

Type 1GbT

Full-duplex

qos trust none

Speed 1000 Mb/s

Auto-negotiation is on

Flow-control: off

Error-control: off

MDI mode: MDIX

VLAN Mode: access

Access VLAN: 1111

Which command will produce the above output?

Show Suggested Answer Hide Answer
Suggested Answer: A

by Kristel at Nov 26, 2023, 04:47 AM

Limited Time Offer

25%

Off

Get Premium HPE6-A72 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel
Ettie
3 months ago
I wonder if the interface is up because it's connected to a PC-1. Maybe the IT guy has a good sense of humor. Anyway, B) is the answer!
upvoted 0 times
...
Lavonna
3 months ago
A) show interface vlan 1111 doesn't sound right, since the output doesn't mention anything about a VLAN interface. B) is the way to go!
upvoted 0 times
Pearly
2 months ago
B) show interface 1/1/1
upvoted 0 times
...
Luisa
2 months ago
A) show interface vlan 1111 doesn't sound right, since the output doesn't mention anything about a VLAN interface. B) is the way to go!
upvoted 0 times
...
Lorean
2 months ago
B) show interface 1/1/1
upvoted 0 times
...
...
Arminda
3 months ago
Hmm, I'm not sure if C) show interface gigabit 1/1/1 would work, since the output doesn't mention 'gigabit' explicitly. I'll go with B) to be safe.
upvoted 0 times
Rusty
2 months ago
User 3: Yeah, B) show interface 1/1/1 seems like the correct choice here.
upvoted 0 times
...
Matthew
2 months ago
User 2: I agree, let's go with B) to be safe.
upvoted 0 times
...
Jordan
2 months ago
User 1: I think B) show interface 1/1/1 is the right command to use.
upvoted 0 times
...
...
Felicidad
4 months ago
The output gives a lot of details about the interface, including the VLAN configuration, so I'm going with B) show interface 1/1/1.
upvoted 0 times
Colette
2 months ago
Great job! It's important to know which command to use for specific information.
upvoted 0 times
...
Jamal
2 months ago
I knew it! The output was very specific.
upvoted 0 times
...
Kenny
2 months ago
That's correct! It provides detailed information about the interface.
upvoted 0 times
...
Albina
2 months ago
B) show interface 1/1/1
upvoted 0 times
...
Lashaunda
2 months ago
Yes, that command will display all the details about interface 1/1/1, including the VLAN configuration.
upvoted 0 times
...
Tequila
3 months ago
I think B) show interface 1/1/1 is the correct command to produce that output.
upvoted 0 times
...
Malcom
3 months ago
Yes, that's right. It provides all the details about the interface including the VLAN configuration.
upvoted 0 times
...
Tequila
3 months ago
I think the correct command is B) show interface 1/1/1
upvoted 0 times
...
...
Sue
4 months ago
This is a straightforward interface status command. I think the correct answer is B) show interface 1/1/1.
upvoted 0 times
Tori
2 months ago
It just takes practice to remember them all.
upvoted 0 times
...
Mireya
2 months ago
I always get confused with these commands.
upvoted 0 times
...
Annett
3 months ago
That's correct!
upvoted 0 times
...
Mona
3 months ago
B) show interface 1/1/1
upvoted 0 times
...
...
Domonique
4 months ago
I'm not sure, but I think C) show interface gigabit 1/1/1 could also be a possible answer
upvoted 0 times
...
Leatha
4 months ago
I agree with Maricela, because the output mentions interface 1/1/1
upvoted 0 times
...
Maricela
4 months ago
I think the answer is B) show interface 1/1/1
upvoted 0 times
...

Save Cancel