HP Exam HPE0-S59 Topic 9 Question 37 Discussion

Actual exam question for HP's HPE0-S59 exam

Question #: 37
Topic #: 9

Your customer plans to use HPE Primera to boot HPE Synergy compute nodes. They currently have two HPE Virtual Connect SE 100Gb F32 Module for Synergy modules installed in the frame. The customer wants to use FC as a storage access protocol

What must be done to complete this task?

AEnable FC primary and secondary boot on the modules through the HPE OneView interface

BFC connectivity on the modules should be enabled through the service console by disabling FCoE.

CAdd FC upgrade licenses in HPE OneView that will enable FC connectivity for the modules

DEnter both modules into a maintenance mode, then enable FC connectivity through CLI

Show Suggested Answer

Suggested Answer: B

by Julianna at May 30, 2024, 09:23 PM

Limited Time Offer

25%

Off

Get Premium HPE0-S59 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Meaghan

1 years ago

Ah, the old 'disable one thing to enable another' trick. I'll stick with Option A, where the magic happens in the magical land of OneView.

upvoted 0 times

Latia

12 months ago

Yeah, OneView is where the magic happens for sure.

upvoted 0 times

...

Lelia

12 months ago

I agree, Option A seems like the way to go.

upvoted 0 times

...

James

1 years ago

You know, I heard HPE Primera is so powerful, it can boot compute nodes just by staring at them. Option C is the obvious choice here.

upvoted 0 times

Frederica

12 months ago

HPE Primera sounds impressive if it can boot compute nodes just by staring at them. Option C with the FC upgrade licenses in HPE OneView is the best choice.

upvoted 0 times

...

Keneth

12 months ago

I agree, Option C seems like the most straightforward solution for enabling FC connectivity on the modules.

upvoted 0 times

...

Cheryl

12 months ago

Option C is definitely the way to go. Adding FC upgrade licenses in HPE OneView will enable FC connectivity for the modules.

upvoted 0 times

...

Zana

1 years ago

Maintenance mode and CLI? Sounds like a lot of unnecessary hassle. Option C is the way to go, keep it simple!

upvoted 0 times

Diego

11 months ago

Yeah, keeping it simple is always the best approach when it comes to these tasks.

upvoted 0 times

...

Makeda

11 months ago

I agree, adding FC upgrade licenses in HPE OneView seems like the most straightforward solution.

upvoted 0 times

...

Billy

12 months ago

Option C is definitely the easiest way to go. No need to mess around with maintenance mode and CLI.

upvoted 0 times

...

Ryann

1 years ago

I disagree, I believe the correct answer is D) Enter both modules into maintenance mode, then enable FC connectivity through CLI.

upvoted 0 times

...

Marguerita

1 years ago

Wait, disabling FCoE to enable FC? That's like trying to fit a square peg in a round hole. I'd go with Option A - let OneView handle the boot configuration.

upvoted 0 times

William

12 months ago

Option A sounds like the best way to go. OneView should make it easier to manage the boot configuration.

upvoted 0 times

...

Ryan

1 years ago

Wait, disabling FCoE to enable FC? That's like trying to fit a square peg in a round hole. I'd go with Option A - let OneView handle the boot configuration.

upvoted 0 times

...

Celeste

1 years ago

Option A) Enable FC primary and secondary boot on the modules through the HPE OneView interface

upvoted 0 times

...

Marshall

1 years ago

Option C seems the most straightforward. Why bother with the service console or maintenance mode when you can just enable FC through the license upgrade in OneView?

upvoted 0 times