Fortinet Exam NSE7_EFW-7.2 Topic 3 Question 19 Discussion

Actual exam question for Fortinet's NSE7_EFW-7.2 exam

Question #: 19
Topic #: 3

[All NSE7_EFW-7.2 Questions]

Exhibit.

Refer to the exhibit, which contains the partial ADVPN configuration of a spoke.

Which two parameters must you configure on the corresponding single hub? (Choose two.)

ASet auto-discovery-sender enable

BSet ike-version 2

CSet auto-discovery-forwarder enable

DSet auto-discovery-receiver enable

Show Suggested Answer

Suggested Answer: A, C

For an ADVPN spoke configuration shown, the corresponding hub must have auto-discovery-sender enabled to send shortcut advertisement messages to the spokes. Also, the hub would need to have auto-discovery-forwarder enabled if it is to forward on those shortcut advertisements to other spokes. This allows the hub to inform all spokes about the best path to reach each other. The ike-version does not need to be reconfigured on the hub if it's already set to version 2 and auto-discovery-receiver is not necessary on the hub because it's the one sending the advertisements, not receiving.

FortiOS Handbook - ADVPN

by Aleta at Jul 12, 2024, 09:48 PM

Limited Time Offer

25%

Off

Get Premium NSE7_EFW-7.2 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Ronnie

10 months ago

Ha! I bet the answer is C and D. That's the only way the spoke and hub can communicate properly. And don't forget to enable the disco ball on the router!

upvoted 0 times

Jean

9 months ago

No, I'm pretty sure it's C and D. That's how the spoke and hub can communicate properly.

upvoted 0 times

...

Shanice

9 months ago

Haha, the disco ball on the router would definitely add some flair to the network setup!

upvoted 0 times

...

Kallie

9 months ago

Yes, enabling auto-discovery-forwarder and auto-discovery-receiver will ensure proper communication between the spoke and hub.

upvoted 0 times

...

Roy

9 months ago

I think the answer is A and B. That's what I remember from the configuration.

upvoted 0 times

...

Hassie

10 months ago

I think you're right, C and D are the correct parameters to configure on the hub.

upvoted 0 times

...

Linette

10 months ago

This is a tricky one, but I'd say A and C are the right choices. The hub needs to have the auto-discovery-sender and auto-discovery-forwarder enabled.

upvoted 0 times

Noelia

9 months ago

Agreed, those are the parameters that must be configured on the hub.

upvoted 0 times

...

Laila

9 months ago

So, A and C it is then.

upvoted 0 times

...

Lasandra

10 months ago

Yeah, the hub needs auto-discovery-sender and auto-discovery-forwarder enabled.

upvoted 0 times

...

Loreta

10 months ago

I think A and C are the correct choices.

upvoted 0 times

...

Jodi

10 months ago

Definitely B and D. The IKE version needs to be set to 2 and the auto-discovery-receiver must be enabled on the hub.

upvoted 0 times

...

Rosann

11 months ago

Yes, that's correct. Both auto-discovery-sender enable and ike-version 2 are required for the hub configuration.

upvoted 0 times

...

Charlie

11 months ago

I believe setting ike-version 2 is also necessary on the hub.

upvoted 0 times

...

Gerry

11 months ago

I think the correct answers are C and D. The spoke needs to have the auto-discovery-forwarder and auto-discovery-receiver enabled on the corresponding hub.

upvoted 0 times