New Year Sale 2026! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Fortinet NSE6_FNC-7.2 Exam - Topic 4 Question 43 Discussion

Actual exam question for Fortinet's NSE6_FNC-7.2 exam
Question #: 43
Topic #: 4
[All NSE6_FNC-7.2 Questions]

By default, if after a successful Layer 2 poll, more than 20 endpoints are seen connected on a single switch port simultaneously, what happens to the port?

Show Suggested Answer Hide Answer
Suggested Answer: A

If more than 20 endpoints are seen connected on a single switch port simultaneously after a successful Layer 2 poll, the port is designated as an uplink. FortiNAC will ignore all physical addresses learned on an uplink port and will not perform any control operations on it


by Teri at Nov 21, 2025, 06:52 AM

Limited Time Offer

25%

Off

Get Premium NSE6_FNC-7.2 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Linwood
10 hours ago
I thought it would just get disabled.
upvoted 0 times
...
Chanel
6 days ago
The port becomes a threshold uplink.
upvoted 0 times
...
Aleta
11 days ago
I'm going with C) The port is added to the Forced Registration group. Seems like a good way to control access and prevent abuse.
upvoted 0 times
...
Chau
16 days ago
B) The port is disabled is the way to go. Can't have that many endpoints causing issues on a single port.
upvoted 0 times
...
Jeannetta
21 days ago
Haha, the "Dead-End VLAN" option sounds like a fun place to get stuck! I'm going with that one.
upvoted 0 times
...
Christa
26 days ago
D) The port is switched into the Dead-End VLAN seems like the most logical choice here. It isolates the problematic port without completely disabling it.
upvoted 0 times
...
Telma
1 month ago
I vaguely remember something about the Dead-End VLAN, but I can't remember if that's the right answer for this scenario.
upvoted 0 times
...
Mable
1 month ago
I’m leaning towards the port becoming a threshold uplink, but I might be mixing it up with another concept we covered.
upvoted 0 times
...
Corrinne
1 month ago
I feel like we practiced a similar question where the port gets added to a specific group, but I can't recall the exact term.
upvoted 0 times
...
Charlesetta
2 months ago
I think I remember something about the port being disabled if too many endpoints are detected, but I'm not entirely sure.
upvoted 0 times
...
Denny
2 months ago
This question is testing our understanding of Layer 2 port security features. I'll need to apply that knowledge to figure out the correct answer.
upvoted 0 times
...
Skye
2 months ago
I'm going to start by eliminating the options that don't seem to fit. Then I'll try to reason through the remaining choices.
upvoted 0 times
...
Wei
2 months ago
I think the correct answer is B) The port is disabled. That's the standard behavior when too many endpoints are connected.
upvoted 0 times
...
Gearldine
2 months ago
Okay, I think I know the answer to this. It's about how the switch handles a port with too many connected endpoints, right?
upvoted 0 times
...
Jerry
3 months ago
I’m leaning towards option C. Forced Registration sounds right.
upvoted 0 times
...
Kris
3 months ago
Definitely C, Forced Registration group!
upvoted 0 times
...
Minna
3 months ago
Hmm, I'm a bit unsure about this one. I'll have to review my notes on Layer 2 port behavior and thresholds.
upvoted 0 times
...
Domonique
3 months ago
This seems like a tricky Layer 2 question. I'll need to think through the different options carefully.
upvoted 0 times
Billy
2 months ago
This is definitely a tricky one!
upvoted 0 times
...
...

Save Cancel