Free Preparation Discussions
MENU
CWNP CWDP-305 Exam Questions
- Topic 1: Define Specifications for the WLAN: This section of the exam measures the skills of a Wireless Network Planner and focuses on gathering business and technical requirements needed for designing wireless LANs. It includes understanding user needs, regulatory and safety constraints, and environmental factors. Candidates are expected to identify critical elements such as coverage, capacity, security, and device compatibility, and to analyse existing infrastructure and documentation to ensure a successful design strategy.
- Topic 2: Design the WLAN: This section of the exam measures the skills of a WLAN Design Engineer and covers the process of selecting configurations, architecture types, and wireless components to meet business and technical requirements. It includes using design software, selecting access points and antennas, and applying methodologies such as predictive or measured design. Candidates must demonstrate the ability to produce effective documentation and configure features like QoS, roaming security, and network services for different types of client devices and applications.
- Topic 3: Deploy the WLAN: This section of the exam measures the skills of a WLAN Implementation Specialist and involves overseeing the deployment phase of wireless networks. It focuses on understanding deployment procedures for various WLAN architectures, configuring supporting infrastructure, and verifying proper installation. The section also addresses physical installation checks, documentation handover, and quality assurance practices during ongoing installations.
- Topic 4: Validate and Optimize the WLAN: This section of the exam measures the skills of a WLAN Optimization Specialist and assesses the ability to test, validate, and fine-tune wireless networks post-deployment. Key tasks include RF validation surveys, performance testing, troubleshooting connectivity and security issues, and applying appropriate physical or RF adjustments. It also involves client testing and final project handover, including documentation, knowledge transfer, and meetings to ensure long-term WLAN success.
Free CWNP CWDP-305 Exam Actual Questions
Note: Premium Questions for CWDP-305 were last updated On Aug. 26, 2026 (see below)
Which of the following items could be considered constraints when performing a network design?(Choose all that apply.)
Assume that your network operates in a regulatory domain that allows use of the entire 5 GHz space allowed in the 802.11ac amendment. In your
upcoming
802.11ac deployment, you would like to take advantage of the performance improvements that result from channel bonding. However, after
extensive testing, you have determined that your mission-critical WLAN should not use channels requiring DFS support.
Given those two criteria (enable channel bonding and disable DFS channels), in the 5 GHz spectrum, how many non-overlapping 40 MHz channels
will your system be able to use?
Given: You are evaluating the theoretical and real-world RF gain benefits of transmit and receive features introduced by 802.11 with MIMO. This
exercise allows you to quantify the features value in a real-world environment.
What is the maximum theoretical signal gain of chip-based TxBF and MRC (as features) when compared to the same AP using only a single
antenna for transmit and receive (effectively simulating a 1x1 chip)?
The maximum theoretical signal gain of chip-based TxBF and MRC depends on the number of antennas and the channel conditions. TxBF (transmit beamforming) is a technique that focuses the transmitted signal in the direction of the intended receiver, resulting in higher signal strength and less interference. MRC (maximum ratio combining) is a technique that combines the signals received by multiple antennas in an optimal way, resulting in higher signal-to-noise ratio and better performance. The theoretical gain of TxBF and MRC can be calculated as
GTxBF=10log10(N)
and
GMRC=10log10(N)
where N is the number of antennas. Therefore, the total gain of TxBF and MRC is
Gtotal=GTxBF+GMRC=20log10(N)
However, this is the ideal case and assumes perfect channel conditions and alignment. In reality, the gain is lower due to factors such as channel fading, antenna spacing, and feedback delay. According to the CWDP study guide1, the typical gain of TxBF and MRC is about 4-6.5 dBi for 2 antennas, 7-10 dBi for 3 antennas, and 10-13 dBi for 4 antennas. Therefore, the answer is D. Reference: 1: CWDP Certified Wireless Design Professional Official Study Guide: Exam PW0-250, Chapter 8, page 267.
During a post-validation assessment, you have configured a client for 802.1X/EAP but it is not passing authentication. Which areas should you check in the WLAN configuration?
Response:
When installing APs on high ceilings, what should be the most common PPE to be used?
- Select Question Types you want
- Set your Desired Pass Percentage
- Allocate Time (Hours : Minutes)
- Create Multiple Practice tests with Limited Questions
- Customer Support
Jeffrey Thomas
23 days agoDorothy Sanchez
1 month agoRyan Hernandez
2 months agoJennifer Walker
2 months agoRonald Harris
3 months agoNathan Rodriguez
3 months agoMichelle Williams
4 months agoKimberly Turner
4 months agoJeffrey Sanchez
4 months agoRobert Johnson
4 months agoLaura Martin
4 months agoTimothy Anderson
4 months agoMark Reed
4 months agoHassie
5 months agoVicky
5 months agoEllen
5 months agoTelma
6 months agoDelmy
6 months agoCarmen
6 months agoAlishia
6 months agoSherly
7 months agoVanda
7 months agoMarget
7 months agoChristoper
7 months agoDaniel
8 months agoValentine
8 months agoLoreta
8 months agoAnnmarie
8 months agoDaren
9 months agoTommy
9 months agoCyril
9 months agoLong
9 months agoElinore
10 months agoBenedict
10 months agoLeonor
10 months agoXuan
10 months agoMelita
11 months agoJoye
11 months agoTimmy
11 months agoAleshia
11 months agoErnest
11 months agoWilda
12 months agoChau
12 months agoIn
1 year agoMarti
1 year agoKris
1 year ago