Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 350-601 Exam - Topic 4 Question 104 Discussion

Refer to the exhibit.Refer to the exhibit. An FCoE-attached storage connects to a Cisco Nexus 9000 Series Switch on interface ethernet1/12. After the configuration was performed. VSAN 200 failed to activate on the vfc interface. Which configuration action must be performed to bring up VSAN 200?
B) Trunk the FCoE VLAN on interface vfc 10.
A) Configure interface vfc 10 as a node port.
C) Change the native VLAN on the trunk port.
D) Bind VSAN 200 on interface ethernet1/12.

Cisco 350-601 Exam - Topic 4 Question 104 Discussion

Actual exam question for Cisco's 350-601 exam
Question #: 104
Topic #: 4
[All 350-601 Questions]

Refer to the exhibit.

Refer to the exhibit. An FCoE-attached storage connects to a Cisco Nexus 9000 Series Switch on interface ethernet1/12. After the configuration was performed. VSAN 200 failed to activate on the vfc interface. Which configuration action must be performed to bring up VSAN 200?

Show Suggested Answer Hide Answer
Suggested Answer: B

by Lashon at Apr 06, 2026, 06:20 PM

Limited Time Offer

25%

Off

Get Premium 350-601 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Oretha
3 days ago
I think B is the safest bet. Trunking is essential for FCoE.
upvoted 0 times
...
Annette
8 days ago
I’m not sure about A. It feels too basic for this scenario.
upvoted 0 times
...
Cristal
13 days ago
I agree with D. Binding VSAN 200 is crucial for activation.
upvoted 0 times
...
Paz
19 days ago
I’m leaning towards A. Node port configuration seems necessary.
upvoted 0 times
...
Edwin
24 days ago
I feel like B could work too. Trunking the FCoE VLAN makes sense.
upvoted 0 times
...
Lasandra
29 days ago
This question is tricky. I think D is the right choice.
upvoted 0 times
...
Caprice
1 month ago
VSAN activation issues can be tricky, but D makes sense!
upvoted 0 times
...
Anisha
1 month ago
Wait, are you sure about that? Seems too simple.
upvoted 0 times
...
Janey
1 month ago
I thought trunking the FCoE VLAN was the answer.
upvoted 0 times
...
Dominque
2 months ago
Definitely option D! That's the way to go.
upvoted 0 times
...
Franchesca
2 months ago
You need to bind VSAN 200 on ethernet1/12.
upvoted 0 times
...
Caprice
2 months ago
Trunking the FCoE VLAN is also crucial for this setup.
upvoted 0 times
...
Reena
2 months ago
Wait, are you sure about that? Sounds off to me.
upvoted 0 times
...
Oren
2 months ago
I thought changing the native VLAN would work too.
upvoted 0 times
...
Launa
4 months ago
Definitely option D! That's the way to go.
upvoted 0 times
...
Lauran
4 months ago
You need to bind VSAN 200 on ethernet1/12.
upvoted 0 times
...
Carin
5 months ago
I feel like binding VSAN 200 on ethernet1/12 is the key action, but I can't recall the exact steps we discussed.
upvoted 0 times
...
Makeda
5 months ago
I’m a bit confused about the node port configuration. Does that really apply to this scenario?
upvoted 0 times
...
Theola
5 months ago
I think we practiced a question like this where we had to trunk the FCoE VLAN. That might be the right answer here.
upvoted 0 times
...
Iola
5 months ago
I remember something about needing to bind the VSAN to the interface, but I'm not sure if it's the ethernet or vfc interface.
upvoted 0 times
...

Save Cancel