Cisco 350-601 Exam - Topic 3 Question 101 Discussion

Actual exam question for Cisco's 350-601 exam

Question #: 101
Topic #: 3

An engineer performs a Cisco UCS C480 ML M5 installation from a Cisco UCS Manager As a part of the design the server must perform an iSCSI bool from the storage array Which configuration must be performed in the SAN settings in the root organization to satisfy that condition?

BCreate a virtual iSCSI vNIC.

CEnable a host SAN pool.

DCreate an IQN suffix pool.

AImplement a WWPN pool.

Show Suggested Answer

Suggested Answer: D

by Evangelina at Jan 28, 2026, 08:52 PM

Limited Time Offer

25%

Off

Get Premium 350-601 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Myra

2 months ago

Don't forget about the target IP address configuration!

upvoted 0 times

...

Salome

2 months ago

Right! Also, configuring the VLAN for iSCSI traffic is crucial.

upvoted 0 times

...

Glenn

2 months ago

Agreed! I think we need to set the iSCSI initiator settings.

upvoted 0 times

...

Rose

2 months ago

This question is tricky! iSCSI boot can be complex.

upvoted 0 times

...

Dalene

2 months ago

Yup, you also have to configure the boot policy correctly!

upvoted 0 times

...

Hoa

4 months ago

I thought iSCSI was only for storage, not booting.

upvoted 0 times

...

Staci

4 months ago

Wait, does that mean we need specific VLANs set up too?

upvoted 0 times

...

Justine

4 months ago

Totally agree, that’s a must for iSCSI boot!

upvoted 0 times

...

Valentin

4 months ago

You need to enable iSCSI boot support in the SAN settings.

upvoted 0 times

...

Francine

5 months ago

Setting up the iSCSI boot in the SAN settings of the root org is the way to go, no doubt about it.

upvoted 0 times

...

Becky

5 months ago

Haha, I bet the engineer wishes they had a Cisco UCS C480 ML M5 to play with instead of just installing it!

upvoted 0 times

...

Sarah

5 months ago

The SAN settings in the root organization are where you need to configure the iSCSI boot.

upvoted 0 times

...

Leila

5 months ago

Definitely need to set up the iSCSI boot configuration in the SAN settings of the root organization.

upvoted 0 times

...

Irma

5 months ago

I think the correct answer is to configure the iSCSI boot settings in the SAN settings of the root organization.

upvoted 0 times

...

Mariann

5 months ago

The iSCSI boot configuration must be set up in the SAN settings of the root organization.

upvoted 0 times

...

Amos

6 months ago

I believe we also have to set the target IQN for the iSCSI boot, but I can't remember if that goes in the root organization or somewhere else.

upvoted 0 times

...

Minna

6 months ago

I practiced a similar question about FC boot configurations last week, but iSCSI feels a bit different. I hope I can recall the specific steps needed.

upvoted 0 times

...

Gwenn

7 months ago

I remember something about configuring the iSCSI initiator and setting the appropriate VLANs for the storage traffic. That might be relevant here.

upvoted 0 times

...

Marti

7 months ago

I think we need to enable iSCSI boot support in the SAN settings, but I'm not entirely sure where to find that option in UCS Manager.

upvoted 0 times

...

Beula

7 months ago

No problem, I've done this kind of configuration before. I'll make sure to double-check the SAN settings in the root organization, especially the iSCSI boot policy, VLAN, and initiator group settings. Shouldn't be too tricky if I remember the right steps.

upvoted 0 times

...

Malcom

7 months ago

Whoa, this is a pretty specific question. I'm not super familiar with Cisco UCS, so I'll need to really focus on understanding the key configuration steps for iSCSI boot in the SAN settings. Might need to review some documentation.

upvoted 0 times

...

Alesia

7 months ago

I think I know how to approach this. I'll need to set up the iSCSI boot policy and make sure the necessary VLAN and initiator group settings are configured in the SAN settings. Gotta be careful to get all the details right.

upvoted 0 times

...

Tomas

7 months ago

Okay, so we need to configure the SAN settings in the root organization to support an iSCSI boot from a storage array. I'll need to review my notes on iSCSI boot configuration in Cisco UCS.

upvoted 0 times

...