Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 350-601 Exam - Topic 2 Question 106 Discussion

A Cisco Unified Computing System environment must be configured for a server that requites access to VLAN 30 for data and VLAN 40 for management The server must have failover capabilities The upstream connectivity will be provided by using a Cisco Nexus 9000 Series Switch. Which action must be taken to meet these requirements?
C) Create a virtual network interface cards for each VLAN and enable vNIC fabric failover
A) Use a single virtual network interface card for both VLANs and assign the vNlC lo a dynamic LAN pin group.
B) Create a virtual network interface card for each VLAN and configure the host to use load balancing.
D) Use a single virtual network interface card for both VLANs and apply a network control policy for prioritization.

Cisco 350-601 Exam - Topic 2 Question 106 Discussion

Actual exam question for Cisco's 350-601 exam
Question #: 106
Topic #: 2
[All 350-601 Questions]

A Cisco Unified Computing System environment must be configured for a server that requites access to VLAN 30 for data and VLAN 40 for management The server must have failover capabilities The upstream connectivity will be provided by using a Cisco Nexus 9000 Series Switch. Which action must be taken to meet these requirements?

Show Suggested Answer Hide Answer
Suggested Answer: C

by Vallie at May 16, 2026, 07:20 PM

Limited Time Offer

25%

Off

Get Premium 350-601 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Salome
3 days ago
This question is tricky! I think option C is the best.
upvoted 0 times
...
Reynalda
8 days ago
D sounds good for prioritization, but not for failover.
upvoted 0 times
...
Deangelo
13 days ago
Definitely need separate vNICs for VLANs.
upvoted 0 times
...
Stevie
19 days ago
Surprised that A is even an option, seems risky!
upvoted 0 times
...
Cherri
24 days ago
I think B is better for load balancing.
upvoted 0 times
...
Phyliss
29 days ago
Option C is the way to go for failover!
upvoted 0 times
...
Lilli
1 month ago
C is the best option here, no doubt about it!
upvoted 0 times
...
Viola
1 month ago
B is a solid choice for load balancing, but not sure about failover.
upvoted 0 times
...
Shanice
1 month ago
Wait, can you really use a single vNIC for both VLANs? Sounds risky!
upvoted 0 times
...
Tarra
2 months ago
I think A could work too, but not ideal for failover.
upvoted 0 times
...
Shay
2 months ago
Option C is definitely the way to go for failover.
upvoted 0 times
...
Heike
2 months ago
I recall that enabling fabric failover is crucial for ensuring connectivity in case one path goes down. That might be the key here.
upvoted 0 times
...
Luisa
2 months ago
I'm a bit unsure about the load balancing part. Does that really apply here if we need failover capabilities?
upvoted 0 times
...
Mabel
2 months ago
This question seems similar to one we practiced where we had to configure VLANs for redundancy. I feel like creating separate vNICs could be the right approach.
upvoted 0 times
...
Yoko
4 months ago
I think I remember that using a single vNIC for both VLANs might not provide the failover we need.
upvoted 0 times
...

Save Cancel