Deal of The Day! Hurry Up, Grab the Special Discount - Save 25% - Ends In 00:00:00 Coupon code: SAVE25
Welcome to Pass4Success

- Free Preparation Discussions
Mail Us support@pass4success.com
Location US
Mob_nav_barsMENU

Cisco 300-820 Exam - Topic 11 Question 94 Discussion

Refer to the exhibit.The firewall has been configured from NAT 192.168.108.2 to 100.64.0.1. Which configuration changes are needed for an Expressway-E with dual network interfaces?A)B)C)D)
D) Option D
A) Option A
B) Option B
C) Option C

Cisco 300-820 Exam - Topic 11 Question 94 Discussion

Actual exam question for Cisco's 300-820 exam
Question #: 94
Topic #: 11
[All 300-820 Questions]

Refer to the exhibit.

The firewall has been configured from NAT 192.168.108.2 to 100.64.0.1. Which configuration changes are needed for an Expressway-E with dual network interfaces?

A)

B)

C)

D)

Show Suggested Answer Hide Answer
Suggested Answer: D

by Adelle at Mar 03, 2025, 10:58 PM

Limited Time Offer

25%

Off

Get Premium 300-820 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

0/2000 characters
Submit Cancel
Viola
9 months ago
I’m not convinced, I’d go with Option A instead.
upvoted 0 times
...
Carmela
9 months ago
Totally agree with you, Franchesca!
upvoted 0 times
...
Ena
10 months ago
Wait, are we sure about the dual interfaces? Seems tricky.
upvoted 0 times
...
Franchesca
10 months ago
I think Option C is the best choice here.
upvoted 0 times
...
Kanisha
10 months ago
The NAT config looks correct for the Expressway-E.
upvoted 0 times
...
Lynelle
10 months ago
I’m leaning towards option D, but I have a nagging doubt about whether it covers both interfaces properly.
upvoted 0 times
...
Adela
11 months ago
I feel like option C might be the right choice, but I can't quite remember the specifics about the Expressway-E setup.
upvoted 0 times
...
Chanel
11 months ago
I think we practiced a similar question in class, and if I recall correctly, it involved adjusting the NAT settings for dual interfaces.
upvoted 0 times
...
Dorcas
11 months ago
I remember something about NAT configurations, but I'm not sure if it's option A or B that applies here.
upvoted 0 times
...
Tawny
11 months ago
I'm a bit confused by the different interface options. Let me re-read the question and review the diagrams again to make sure I understand the requirements before selecting an answer.
upvoted 0 times
...
Shawna
11 months ago
Okay, I see the dual network interfaces on the Expressway-E. I'm pretty confident that Option D is the correct configuration to make this work with the NAT firewall setup.
upvoted 0 times
...
Stephane
11 months ago
Hmm, the firewall is configured for NAT, so I'll need to consider how that impacts the Expressway-E interfaces. I'm not totally sure, but I think Option B might be the right answer.
upvoted 0 times
...
Kathryn
11 months ago
This looks like a tricky firewall and Expressway-E configuration question. I'll need to carefully analyze the network diagram and options to determine the right changes needed.
upvoted 0 times
...
Tarra
11 months ago
I'm feeling pretty confident about this one. The firewall configuration is straightforward, and the dual network interfaces on the Expressway-E just require a simple NAT change. I'll select the option that best matches the requirements.
upvoted 0 times
...
Trina
11 months ago
Okay, I think I've got this. The key is to identify the correct NAT configuration that will allow the Expressway-E to communicate with the 100.64.0.1 network. I'll carefully compare the options to find the right solution.
upvoted 0 times
...
Rutha
11 months ago
Hmm, I'm a bit confused by the dual network interfaces on the Expressway-E. I'll need to review the networking concepts to make sure I understand how that impacts the firewall configuration.
upvoted 0 times
...
Earleen
11 months ago
This looks like a tricky firewall configuration question. I'll need to carefully analyze the network diagram and the options to determine the right changes for the Expressway-E.
upvoted 0 times
...

Save Cancel