Cisco 300-710 Exam - Topic 9 Question 108 Discussion

Actual exam question for Cisco's 300-710 exam

Question #: 108
Topic #: 9

An engineer is troubleshooting a device that cannot connect to a web server. The connection is initiated from the Cisco FTD inside interface and attempting to reach 10.0.1.100 over the non-standard port of 9443 The host the engineer is attempting the connection from is at the IP address of 10.20.10.20. In order to determine what is happening to the packets on the network, the engineer decides to use the FTD packet capture tool Which capture configuration should be used to gather the information needed to troubleshoot this issue?

AOption A

BOption B

COption C

DOption D

Show Suggested Answer

Suggested Answer: B

by Lajuana at Apr 04, 2025, 04:43 PM

Limited Time Offer

25%

Off

Get Premium 300-710 Questions as Interactive Web-Based Practice Test or PDF

Contribute your Thoughts:

Submit Cancel

Kristel

9 months ago

Wait, why is it using a non-standard port? That's odd!

upvoted 0 times

...

Kandis

9 months ago

Definitely going with Option C for this one!

upvoted 0 times

...

Rosalyn

9 months ago

Not sure about that, B seems more relevant to me.

upvoted 0 times

...

Magdalene

9 months ago

Gotta check the inside interface settings too!

upvoted 0 times

...

Moon

9 months ago

The connection is on port 9443, so we need to capture that.

upvoted 0 times

...

Major

10 months ago

I’m leaning towards Option B, but I’m not entirely confident about the filter settings for the specific port.

upvoted 0 times

...

Van

10 months ago

I feel like I’ve seen a similar question before, but I can’t recall if it was about a standard or non-standard port.

upvoted 0 times

...

Rosio

10 months ago

I think we need to capture traffic on the inside interface, right? That’s where the connection starts.

upvoted 0 times

...

Trinidad

10 months ago

I remember we practiced packet captures, but I'm not sure which interface to select for the FTD.

upvoted 0 times

...

Brynn

11 months ago

I've got a good feeling about Option B. The capture configuration seems to be the most comprehensive and should give me the visibility I need to identify what's happening with the packets.

upvoted 0 times

...

Iesha

11 months ago

Hmm, this is a tough one. I'm a bit confused by the different packet capture options. I'll need to think through each one carefully to figure out which one will give me the information I need to troubleshoot this issue.

upvoted 0 times

...

Hayley

11 months ago

Okay, let's see. The key details are that the connection is from the FTD inside interface to a non-standard port on the web server. I think Option C might be the way to go, but I'll double-check the other options just to be sure.

upvoted 0 times

...

Caitlin

11 months ago

This looks like a tricky one. I'll need to carefully review the details of the network connection and the packet capture options to determine the best approach.

upvoted 0 times

...

Linwood

1 year ago

Option B is the way to go, just like my grandma used to say, 'Keep it simple, stupid' - or was that the CIA? Anyway, it works for this question too!

upvoted 0 times

Arleen

1 year ago

Yeah, sometimes the simplest option is the most effective.

upvoted 0 times

...

Kayleigh

1 year ago

I agree, keeping it simple is usually the best approach.

upvoted 0 times

...

Arlene

1 year ago

Option B is definitely the best choice here.

upvoted 0 times

...

Ronald

1 year ago

Option A, really? Who uses a packet capture tool to troubleshoot a web server connection issue? That's like using a sledgehammer to crack a nut.

upvoted 0 times

...

Becky

1 year ago

This is a tricky one, but I think Option D is the best bet. Capturing the traffic on both interfaces and using the advanced options to filter should give us a clear picture of what's happening.

upvoted 0 times

Ivette

1 year ago

I'm not sure, but Option A could be a good starting point to see if we can isolate the issue with the packet capture.

upvoted 0 times

...

Truman

1 year ago

I think Option C might also work well, as it focuses on capturing traffic specifically on the inside interface.

upvoted 0 times

...

Von

1 year ago

I agree, Option D seems like the most comprehensive choice for capturing the necessary information.

upvoted 0 times

...

Sueann

1 year ago

I see your point, but I think Option A would provide more detailed information for troubleshooting.

upvoted 0 times

...

Shoshana

1 year ago

I disagree, I believe Option C would be more appropriate in this scenario.

upvoted 0 times

...

Cary

1 year ago

I'm going with Option C. Capturing on the outside interface and filtering for the source IP and destination port sounds like the right approach.

upvoted 0 times

Augustine

1 year ago

Let's go with Option C then. It seems like the most efficient way to gather the necessary data for troubleshooting.

upvoted 0 times

...

Nilsa

1 year ago

Agreed, capturing on the outside interface and filtering for the specific source IP and destination port will give us the targeted information.

upvoted 0 times

...

Michell

1 year ago

I think Option C is the best choice too. It will help us filter the packets we need to troubleshoot.

upvoted 0 times

...

Glynda

1 year ago

Option B looks like the way to go. Capturing the traffic on the inside interface and filtering for the specific IP and port should give us the info we need.

upvoted 0 times